1301380032 Molex Inc, 1301380032 Datasheet - Page 189

• Manufacturer Part Number: 1301380032
• Description: COVERPLATE - WITH FLIP LID
• Manufacturer: Molex Inc
• Series: 130138r

Specifications of 1301380032

• Accessory Type: Cover Plate
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 0130138-0032; 0130138-0032-E; 01301380032; 01301380032-E; 130138-0032; 130138-0032-E; 1301380032-E; 3061

www.woodhead.com
Grip Cable Range Conversion
Strength Information
The approximate breaking strength of any Woodhead wire mesh cable grip is based on working load information established by
Woodhead engineering laboratories. In making these determinations, it is not possible to cover all applications and operating
conditions. Variables such as diameters, gripping surfaces, number of items gripped, tension, movement, attachment, abrasion,
corrosion, prior use, or abuse must be assessed by the user. Greater safety factors should be utilized when the conditions of
application are vague or unknown.
For specific applications where strength and holding power are important, consult the manufacturer. To determine the
recommended working load safety factor for listed cable grips, divide the approximate breaking strength by 5 for pulling grips
and 10 for support grips. Woodhead maintains a 6 sigma safety factor for pulling grips and a 5 sigma safety factor for support
grips for these recommended working loads (using average break strengths obtained on new grips under lab test conditions).
Example: For pulling grips – 33,000÷5=6,600 lbs. which is the workload factor.
Example: For support grips – 10,080÷10=1,008 lbs. which is the workload factor.
All warranties concerning product quality or performance are based on wire mesh grips that are properly stored and handled by
the user, and grips that are maintained and inspected at a proper frequency in keeping with their use and condition.
Split Lace/Split Rod attachments
(for use where end of cable is not accessible)
Beginning at the end of the grip closest to the bale fitting, thread the lacing
through the first two loops of the split, pulling lace through until ends are centered
evenly. Cross laces and thread through next two loops, and so on down the grip,
being careful not to pull lacing too tight. Spacing of laced closure should be
approximately the same as mesh weave. When end of grip is reached, twist lacing
strands tightly together, wrap ends of lace around grip, and twist again to secure.
Excess length may be cut off.
Split grips with rod closing are economical, since they are quickly installed, and
are reusable. Simply wrap the grip around the cable and thread the rod through
the loops, using a corkscrew motion. To remove, pull the rod out, and the grip is
ready for re-use.
1
3
1
5
3
1 - 1
1
1
2 - 2
2
3 - 3
3
⁄
⁄
⁄
⁄
⁄
4
8
2
8
4
1
1
1
1
⁄
⁄
⁄
⁄
-
-
-
-
-
4
2
2
2
- 1
- 1
- 2
- 3
23
31
39
47
63
⁄
⁄
⁄
⁄
⁄
15
31
31
6 4
6 4
6 4
6 4
6 4
⁄
⁄
⁄
6 4
31
63
6 4
63
6 4
63
"
"
"
"
"
(FRACTIONAL)
"
⁄
⁄
"
⁄
"
⁄
6 4
6 4
6 4
6 4
"
"
"
"
INCHES
0.25-0.36"
0.37-0.49"
0.50-0.61"
0.62-0.74"
0.75-0.99"
1.00-1.24"
1.25-1.49"
1.50-1.99"
2.00-2.49"
2.50-2.99"
3.00-3.49"
3.50-3.99"
(DECIMAL)
INCHES
6.35-9.13 mm
9.52-12.30 mm
12.70-15.48 mm
15.88-18.65 mm
19.05-25.00 mm
25.40-31.35 mm
31.75-37.70 mm
38.10-50.40 mm
50.80-63.10 mm
63.50-75.80 mm
76.20-88.50 mm
88.90-101.20 mm
METRIC
(MM)
PULLING AND SUPPORT GRIPS
Split-Lace
Split-Rod
CABLE GRIPS
WOODHEAD 187