IDT89HPES4T4G2ZCALG8 IDT, Integrated Device Technology Inc, IDT89HPES4T4G2ZCALG8 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT89HPES4T4G2ZCALG8
Manufacturer Part Number
IDT89HPES4T4G2ZCALG8
Description
IC PCI SW 4LANE 4PORT 324-FCBGA
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT89HPES4T4G2ZCAL8.pdf
(29 pages)
Specifications of IDT89HPES4T4G2ZCALG8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
89HPES4T4G2ZCALG8
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT89HPES4T4G2ZCALG8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
IDT 89HPES4T4G2 Data Sheet
JTAG_TRST_N
SWMODE[2:0]
JTAG_TCK
JTAG_TDO
JTAG_TMS
JTAG_TDI
Signal
CCLKDS
CCLKUS
PERSTN
Signal
Type
Type
O
I
I
I
I
I
I
I
I
Common Clock Downstream. The assertion of this pin indicates that all
downstream ports are using the same clock source as that provided to
downstream devices.This bit is used as the initial value of the Slot Clock
Configuration bit in all of the Link Status Registers for downstream ports.
The value may be overridden by modifying the SCLK bit in each down-
stream port’s PCIELSTS register.
Common Clock Upstream. The assertion of this pin indicates that the
upstream port is using the same clock source as the upstream device. This
bit is used as the initial value of the Slot Clock Configuration bit in the Link
Status Register for the upstream port. The value may be overridden by
modifying the SCLK bit in the P0_PCIELSTS register.
Fundamental Reset. Assertion of this signal resets all logic inside
PES4T4G2 and initiates a PCI Express fundamental reset.
Switch Mode. These configuration pins determine the PES4T4G2 switch
operating mode.
0x0 - Normal switch mode
0x1 - Normal switch mode with Serial EEPROM initialization
0x2 - through 0x7 Reserved
These pins should be static and not change following the negation of
PERSTN.
JTAG Clock. This is an input test clock used to clock the shifting of data
into or out of the boundary scan logic or JTAG Controller. JTAG_TCK is
independent of the system clock with a nominal 50% duty cycle.
JTAG Data Input. This is the serial data input to the boundary scan logic or
JTAG Controller.
JTAG Data Output. This is the serial data shifted out from the boundary
scan logic or JTAG Controller. When no data is being shifted out, this signal
is tri-stated.
JTAG Mode. The value on this signal controls the test mode select of the
boundary scan logic or JTAG Controller.
JTAG Reset. This active low signal asynchronously resets the boundary
scan logic and JTAG TAP Controller. An external pull-up on the board is
recommended to meet the JTAG specification in cases where the tester
can access this signal. However, for systems running in functional mode,
one of the following should occur:
1) actively drive this signal low with control logic
2) statically drive this signal low with an external pull-down on the board
Table 4 System Pins
Table 5 Test Pins
6 of 29
Name/Description
Name/Description
September 13, 2010