IR3082AMTRPBF International Rectifier, IR3082AMTRPBF Datasheet - Page 6

• Manufacturer Part Number: IR3082AMTRPBF
• Description: IC XPHASE CONTROL 9.6V 20-MLPQ
• Manufacturer: International Rectifier
• Series: XPhase™r

Specifications of IR3082AMTRPBF

• Applications: Processor
• Current - Supply: 12mA
• Voltage - Supply: 8.05 V ~ 16 V
• Operating Temperature: 0°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 20-MLPQ
• Ic Function: Control IC
• Supply Voltage Range: 8.05V To 16V
• Operating Temperature Range: 0°C To +100°C
• Digital Ic Case Style: MLPQ
• No. Of Pins: 20
• Filter Terminals: SMD
• Supply Voltage Min: 9.6V
• Rohs Compliant: Yes
• Controller Type: PWM
• Frequency: 1MHz
• Package: 20-Lead MLPQ
• Circuit: X-Phase Control IC
• Switch Freq (khz): 150kHz to 1.0MHz
• Pbf: PbF Option Available
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: IR3082AMTRPBFTR

SYSTEM THEORY OF OPERATION
XPhase
The XPhase
requiring small size, design flexibility, low voltage, high current, and fast transient response. The architecture can
be used in any multiphase converter ranging from 1 to 16 or more phases where flexibility facilitates the design
trade-off of multiphase converters. The scalable architecture can be applied to other applications which require
high current or multiple output voltages.
As shown in Figure 2, the XPhase
each using a single Phase IC. The Control IC communicates with the Phase ICs through a 5-wire analog bus, i.e.
bias voltage, phase timing, average current, error amplifier output, and VID voltage. The Control IC incorporates all
the system functions, i.e. VID, PWM ramp oscillator, error amplifier, bias voltage, and fault protections etc. The
Phase IC implements the functions required by the converter of each phase, i.e. the gate drivers, PWM comparator
and latch, over-voltage protection, and current sensing and sharing.
There is no unused or redundant silicon with the XPhase
controller that can be configured for 2, 3, or 4 phase operation. PCB Layout is easier since the 5 wire bus
eliminates the need for point-to-point wiring between the Control IC and each Phase. The critical gate drive and
current sense connections are short and local to the Phase ICs. This improves the PCB layout by lowering the
parasitic inductance of the gate drive circuits and reducing the noise of the current sense signal.
Page 6 of 33
ENABLE
TM
12V
VID5
VID0
VID1
VID2
VID3
VID4
Architecture
TM
architecture is designed for multiphase interleaved buck converters which are used in applications
IR3082A
CONTROL
IC
>> BIAS VOLTAGE
>> PHASE TIMING
<< CURRENT SENSE
>> PWM CONTROL
>> VID VOLTAGE
TM
CONTROL BUS
architecture consists of a Control IC and a scalable array of phase converters
Figure 2 – System Block Diagram
PHASE FAULT
CURRENT SHARE
PHASE HOT
PHASE FAULT
CURRENT SHARE
PHASE HOT
ADDITIONAL PHASES
IR3086A
PHASE
IC
IR3086A
PHASE
IC
TM
architecture compared to others such as a 4 phase
CCS
CCS
0.1uF
0.1uF
RCS
RCS
INPUT/OUTPUT
CIN
COUT
05/02/2006
IR3082A
POWER GOOD
PHASE FAULT
VR HOT
VOUT SENSE+
VOUT+
VOUT-
VOUT SENSE-