LT1158ISW#TRPBF Linear Technology, LT1158ISW#TRPBF Datasheet - Page 14
![IC MOSFET DVR 1/2BRDG NCH 16SOIC](/photos/6/63/66314/161-16-soic_sml.jpg)
LT1158ISW#TRPBF
Manufacturer Part Number
LT1158ISW#TRPBF
Description
IC MOSFET DVR 1/2BRDG NCH 16SOIC
Manufacturer
Linear Technology
Datasheet
1.LT1158CNPBF.pdf
(22 pages)
Specifications of LT1158ISW#TRPBF
Configuration
Half Bridge
Input Type
PWM
Current - Peak
500mA
Number Of Configurations
1
Number Of Outputs
2
High Side Voltage - Max (bootstrap)
56V
Voltage - Supply
5 V ~ 30 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.300", 7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Delay Time
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT1158
APPLICATIONS INFORMATION
of the LT1158 current limit loop, an initial current spike of
from 2 to 5 times the fi nal value will be present for a few
μs, followed by an interval in which I
spike is normally well within the safe operating area (SOA)
of the MOSFET, but can be further reduced with a small
(0.5μH) inductor in series with the output.
If neither the enable nor input pins are pulled low in
response to the fault indication, the top MOSFET current
will recover to a steady-state value I
LT1158 as shown in Figure 8:
The time for the current to recover to I
initial current spike is approximately Q
Q
be set higher than the required start-up current for mo-
tors (see Starting High In-Rush Current Loads). Note that
14
GS
I
R
I
R
r current
SC
SC
=
SENSE
SENSE
is the MOSFET gate-to-source charge. I
Figure 8. Top MOSFET Short-Circuit Turn-On current
=
=
r 150mV
150mV
R
(
R
SENSE
=
=
S S ENSE
r 150mV
150mV
sense ratio, V = V
(
I
SC
I
SC
)
⎛
⎝ ⎜
1
−
)
⎛
⎝ ⎜
150mV
1
Δ
Δ
−
5μs/DIV
V
1 1 50mV
Δ
⎞
⎠ ⎟
G G S
V
−
2
=
⎞
⎠ ⎟
SC
DS
V
I
−
SC
GS
GS
2
regulated by the
SC
= 0. The current
−
/0.5mA, where
LT1158 F08
following the
V
SC
T
need not
the value of R
the current sensing ratio (typically 1000 – 3000), thus
eliminating the need for a low valued shunt. ΔV is in the
range of 1V to 3V in most applications.
Assuming a dead short, the MOSFET dissipation will rise
to V
= 10A, the dissipation would be 240W. To determine how
long the MOSFET can remain at this dissipation level before
it must be shut down, refer to the SOA curves given in
the MOSFET data sheet. For example, an IRFZ34 would
be safe if shut down within 10ms.
A Tektronix A6303 current probe is highly recommended
for viewing output fault currents.
If Short-Circuit Protection is Not Required
In applications which do not require the current sense
capability of the LT1158, the sense pins 11 and 12 should
both be connected to pin 13, and the FAULT pin 5 left
open. The enable pin 4 may still be used to shut down
the device. Note, however, that when unprotected the top
MOSFET can be easily (and often dramatically) destroyed
by even a momentary short.
Self-Protection with Automatic Restart
When using the current sense circuits of Figures 6 and 7,
local shutdown can be achieved by connecting the FAULT
pin through resistor R
Figure 9. An optional thermostat mounted to the load or
MOSFET heatsink can also be used to pull enable low.
An internal 25μA current source normally keeps the enable
capacitor CEN charged to the 7.5V clamp voltage (or to V
for V
below the enable low threshold (1.15V typ) which shuts
down both MOSFETs. When the FAULT pin or thermostat
releases, CEN recharges to the upper enable threshold
where restart is attempted. In a sustained short circuit,
FAULT will again pull low and the cycle will repeat until the
short is removed. The time to shut down for a DC input
or thermal fault is given by:
t
SHUTDOWN
SUPPLY
+
< 7.5V). When a fault occurs, CEN is discharged to
• I
SC
SENSE
= (100 + 0.8R
. For example, with a 24V supply and I
for the 5-lead MOSFET increases by
F
to the enable pin as shown in
F
) C
EN
DC input
1158fb
SC
+
,