M25P05-AVMN6T NUMONYX, M25P05-AVMN6T Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M25P05-AVMN6T
Manufacturer Part Number
M25P05-AVMN6T
Description
IC FLASH 512KBIT 40MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P05-AVMN6T.pdf
(42 pages)
Specifications of M25P05-AVMN6T
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
512K (64K x 8)
Speed
40MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-1621-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P05-AVMN6TP
Manufacturer:
FREESCALE
Quantity:
110
Company:
Part Number:
M25P05-AVMN6TP
Manufacturer:
NUMONYX
Quantity:
2 350
Part Number:
M25P05-AVMN6TP
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M25P05-AVMN6TP(25P05VP)
Manufacturer:
TI
Quantity:
13
M25P05-A
Page Program (PP)
The Page Program (PP) instruction allows bytes to
be programmed in the memory (changing bits from
1 to 0). Before it can be accepted, a Write Enable
(WREN) instruction must previously have been ex-
ecuted. After the Write Enable (WREN) instruction
has been decoded, the device sets the Write En-
able Latch (WEL).
The Page Program (PP) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, three address bytes and at least
one data byte on Serial Data Input (D). If the 8
least significant address bits (A7-A0) are not all
zero, all transmitted data that goes beyond the end
of the current page are programmed from the start
address of the same page (from the address
whose 8 least significant bits (A7-A0) are all zero).
Chip Select (S) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in
If more than 256 bytes are sent to the device, pre-
viously latched data are discarded and the last 256
data bytes are guaranteed to be programmed cor-
rectly within the same page. If less than 256 Data
bytes are sent to device, they are correctly pro-
grammed at the requested addresses without hav-
20/42
Figure 15.
ing any effects on the other bytes of the same
page.
For optimized timings, it is recommended to use
the Page Program (PP) instruction to program all
consecutive targeted Bytes in a single sequence
versus using several Page Program (PP) se-
quences with each containing only a few Bytes
(see
Chip Select (S) must be driven High after the
eighth bit of the last data byte has been latched in,
otherwise the Page Program (PP) instruction is not
executed.
As soon as Chip Select (S) is driven High, the self-
timed Page Program cycle (whose duration is t
is initiated. While the Page Program cycle is in
progress, the Status Register may be read to
check the value of the Write In Progress (WIP) bit.
The Write In Progress (WIP) bit is 1 during the self-
timed Page Program cycle, and is 0 when it is
completed. At some unspecified time before the
cycle is completed, the Write Enable Latch (WEL)
bit is reset.
A Page Program (PP) instruction applied to a page
which is protected by the Block Protect (BP1, BP0)
bits (see
Instruction
Table 3.
Times).
and
Table
2.) is not executed.
PP
)