M25P05-AVMN6T NUMONYX, M25P05-AVMN6T Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M25P05-AVMN6T
Manufacturer Part Number
M25P05-AVMN6T
Description
IC FLASH 512KBIT 40MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P05-AVMN6T.pdf
(42 pages)
Specifications of M25P05-AVMN6T
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
512K (64K x 8)
Speed
40MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-1621-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P05-AVMN6TP
Manufacturer:
FREESCALE
Quantity:
110
Company:
Part Number:
M25P05-AVMN6TP
Manufacturer:
NUMONYX
Quantity:
2 350
Part Number:
M25P05-AVMN6TP
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M25P05-AVMN6TP(25P05VP)
Manufacturer:
TI
Quantity:
13
INSTRUCTIONS
All instructions, addresses and data are shifted in
and out of the device, most significant bit first.
Serial Data Input (D) is sampled on the first rising
edge of Serial Clock (C) after Chip Select (S) is
driven Low. Then, the one-byte instruction code
must be shifted in to the device, most significant bit
first, on Serial Data Input (D), each bit being
latched on the rising edges of Serial Clock (C).
The instruction set is listed in
Every instruction sequence starts with a one-byte
instruction code. Depending on the instruction,
this might be followed by address bytes, or by data
bytes, or by both or none. Chip Select (S) must be
driven High after the last bit of the instruction se-
quence has been shifted in.
In the case of a Read Data Bytes (READ), Read
Data Bytes at Higher Speed (Fast_Read), Read
Identification (RDID), Read Status Register (RD-
SR) or Release from Deep Power-down, and
Read Electronic Signature (RES) instruction, the
Table 4. Instruction Set
Note: 1. The Read Identification (RDID) instruction is available only in products with Process Technology code X (see Application Note
FAST_READ Read Data Bytes at Higher Speed
Instruction
RDID
WREN
WRSR
RDSR
READ
WRDI
RES
PP
SE
BE
DP
AN1995).
(1)
Write Enable
Write Disable
Read Identification
Read Status Register
Write Status Register
Read Data Bytes
Page Program
Sector Erase
Bulk Erase
Deep Power-down
Release from Deep Power-down,
and Read Electronic Signature
Release from Deep Power-down
Description
Table 4.
One-byte Instruction Code
0000 0110
0000 0100
1001 1111
0000 0101
0000 0001
0000 0011
0000 1011
0000 0010
1101 1000
1100 0111
1011 1001
1010 1011
shifted-in instruction sequence is followed by a
data-out sequence. Chip Select (S) can be driven
High after any bit of the data-out sequence is be-
ing shifted out.
In the case of a Page Program (PP), Sector Erase
(SE), Bulk Erase (BE), Write Status Register
(WRSR), Write Enable (WREN), Write Disable
(WRDI) or Deep Power-down (DP) instruction,
Chip Select (S) must be driven High exactly at a
Byte boundary, otherwise the instruction is reject-
ed, and is not executed. That is, Chip Select (S)
must driven High when the number of clock pulses
after Chip Select (S) being driven Low is an exact
multiple of eight.
All attempts to access the memory array during a
Write Status Register cycle, Program cycle or
Erase cycle are ignored, and the internal Write
Status Register cycle, Program cycle or Erase cy-
cle continues unaffected.
ABh
0Bh
D8h
C7h
06h
04h
9Fh
05h
01h
03h
02h
B9h
Address
Bytes
0
0
0
0
0
3
3
3
3
0
0
0
0
Dummy
Bytes
0
0
0
0
0
0
1
0
0
0
0
3
0
M25P05-A
1 to 256
Bytes
1 to 3
1 to
1 to
1 to
1 to
Data
0
0
1
0
0
0
0
11/42