M25P16-VME6TG NUMONYX, M25P16-VME6TG Datasheet - Page 22
![IC FLASH 16MBIT 75MHZ 8VDFPN](/photos/7/28/72832/m25p16-vme6tg_sml.jpg)
M25P16-VME6TG
Manufacturer Part Number
M25P16-VME6TG
Description
IC FLASH 16MBIT 75MHZ 8VDFPN
Manufacturer
NUMONYX
Series
Forté™r
Specifications of M25P16-VME6TG
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
16M (2M x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-VDFPN
Cell Type
NOR
Density
16Mb
Access Time (max)
15ns
Interface Type
Serial (SPI)
Boot Type
Not Required
Address Bus
1b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
VDFPN EP
Program/erase Volt (typ)
2.7 to 3.6V
Sync/async
Synchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8b
Number Of Words
2M
Supply Current
8mA
Mounting
Surface Mount
Pin Count
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P16-VME6TG
M25P16-VME6TGTR
M25P16-VME6TGTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P16-VME6TG
Manufacturer:
NUMONYX
Quantity:
8 000
6.3
Note:
Table 5.
Figure 10. Read Identification (RDID) instruction sequence and data-out sequence
22/56
Manufacturer
identification
20h
Read Identification (RDID)
The Read Identification (RDID) instruction allows to read the device identification data:
l
l
l
The manufacturer identification is assigned by JEDEC, and has the value 20h for Numonyx.
The device identification is assigned by the device manufacturer, and indicates the memory
type in the first byte (20h), and the memory capacity of the device in the second byte (15h).
The UID contains the length of the following data in the first byte (set to 10h), and 16 bytes
of the optional Customized Factory Data (CFD) content. The CFD bytes are read-only and
can be programmed with customers data upon their request. If the customers do not make
requests, the devices are shipped with all the CFD bytes programmed to zero (00h).
See
Any Read Identification (RDID) instruction while an Erase or Program cycle is in progress, is
not decoded, and has no effect on the cycle that is in progress.
The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code
for the instruction is shifted in. After this, the 24-bit device identification, stored in the
memory, the 8-bit CFD length followed by 16 bytes of CFD content will be shifted out on
Serial Data output (Q). Each bit is shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in
The Read Identification (RDID) instruction is terminated by driving Chip Select (S) High at
any time during data output.
When Chip Select (S) is driven High, the device is put in the Standby Power mode. Once in
the Standby Power mode, the device waits to be selected, so that it can receive, decode and
execute instructions.
Read Identification (RDID) data-out sequence
Section 12: Part numbering on page 54
Manufacturer identification (1 byte)
Device identification (2 bytes)
A Unique ID code (UID) (17 bytes, of which 16 available upon customer request).
Memory type
20h
Device identification
Memory capacity
15h
Figure
for CFD programmed devices.
10.
CFD length
10h
UID
CFD content
16 bytes