AT25DF161-SH-B Atmel, AT25DF161-SH-B Datasheet - Page 32

• Manufacturer Part Number: AT25DF161-SH-B
• Description: IC FLASH 16MBIT 100MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT25DF161-SH-B

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 16M (2M x 8)
• Speed: 100MHz
• Interface: SPI, RapidS
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Density: 16Mb
• Access Time (max): 5ns
• Interface Type: Serial (SPI)
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: SOIC EIAJ
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 2M
• Supply Current: 19mA
• Mounting: Surface Mount
• Pin Count: 8
• Mounting Style: SMD/SMT
• Memory Configuration: 8192 Pages X 256 Bytes
• Clock Frequency: 100MHz
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: SOIC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.1.3 WPP Bit
11.1.4 SWP Bits
11.1.5 WEL Bit
11.1.6 RSTE Bit
11.1.7 SLE Bit
32
The WPP bit can be read to determine if the WP pin has been asserted or not.
The SWP bits provide feedback on the software protection status for the device. There are three possible combinations of
the SWP bits that indicate whether none, some, or all of the sectors have been protected using the Protect Sector
command or the Global Protect feature. If the SWP bits indicate that some of the sectors have been protected, then the
individual Sector Protection Registers can be read with the Read Sector Protection Registers command to determine which
sectors are in fact protected.
The WEL bit indicates the current status of the internal Write Enable Latch. When the WEL bit is in the logical “0” state,
the device will not accept any Byte/Page Program, erase, Protect Sector, Unprotect Sector, Sector Lockdown, Freeze
Sector Lockdown State, Program OTP Security Register, or Write Status Register commands. The WEL bit defaults to the
logical “0” state after a device power-up or reset operation. In addition, the WEL bit will be reset to the logical “0” state
automatically under the following conditions:
If the WEL bit is in the logical “1” state, it will not be reset to a logical “0” if an operation aborts due to an incomplete or
unrecognized opcode being clocked into the device before the CS pin is deasserted. In order for the WEL bit to be reset
when an operation aborts prematurely, the entire opcode for a Byte/Page Program, erase, Protect Sector, Unprotect
Sector, Sector Lockdown, Freeze Sector Lockdown State, Program OTP Security Register, or Write Status Register
command must have been clocked into the device.
The RSTE bit is used to enable or disable the Reset command. When the RSTE bit is in the logical “0” state (the default
state after power-up), the Reset command is disabled and any attempts to reset the device using the Reset command will
be ignored. When the RSTE bit is in the logical “1” state, the Reset command is enabled.
The RSTE bit will retain its state as long as power is applied to the device. Once set to the logical “1” state, the RSTE bit
will remain in that state until it is modified using the Write Status Register Byte 2 command or until the device has been
power cycled. The Reset command itself will not change the state of the RSTE bit.
The SLE bit is used to enable and disable the Sector Lockdown and Freeze Sector Lockdown State commands. When the
SLE bit is in the logical “0” state (the default state after power-up), the Sector Lockdown and Freeze Sector Lockdown
commands are disabled. If the Sector Lockdown and Freeze Sector Lockdown commands are disabled, then any attempts
to issue the commands will be ignored. This provides a safeguard for these commands against accidental or erroneous
•
•
•
•
•
•
•
•
•
•
•
Atmel AT25DF161
Write Disable operation completes successfully
Write Status Register operation completes successfully or aborts
Protect Sector operation completes successfully or aborts
Unprotect Sector operation completes successfully or aborts
Sector Lockdown operation completes successfully or aborts
Freeze Sector Lockdown State operation completes successfully or aborts
Program OTP Security Register operation completes successfully or aborts
Byte/Page Program operation completes successfully or aborts
Block Erase operation completes successfully or aborts
Chip Erase operation completes successfully or aborts
Hold condition aborts
3687E–DFLASH–11/10