IS61C1024AL-12JI-TR ISSI, IS61C1024AL-12JI-TR Datasheet
IS61C1024AL-12JI-TR
Specifications of IS61C1024AL-12JI-TR
Related parts for IS61C1024AL-12JI-TR
IS61C1024AL-12JI-TR Summary of contents
Page 1
... When CE1 is HIGH or CE2 is LOW (deselected), the device assumes a standby mode at which the power dissipation can be reduced by using CMOS input levels. Easy memory expansion is provided by using two Chip Enable inputs, CE1 and CE2 active LOW W rite Enable (WE) controls both writing and reading of the memory. The IS61C1024AL/IS64C1024AL is available in 32-pin 300-mil SOJ, 32-pin 400-mil SOJ, 32-pin TSOP (Type I, 8x20), and 32-pin sTSOP (Type 13.4) packages. DECODER MEMORY ARRAY I/O COLUMN I/O DATA ...
Page 2
... A13 CE2 6 A15 7 VDD A16 10 A14 11 A12 OPERATING RANGE (IS61C1024AL) Range Commercial 0°C to +70°C Industrial OPERATING RANGE (IS64C1024AL) Range Automotive I/O Operation High High High ...
Page 3
... IS61C1024AL, IS64C1024AL ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND term t Storage Temperature stg P Power Dissipation Output Current (LOW) out Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating con- ditions for extended periods may affect reliability. CAPACITANCE (1,2) Symbol Parameter c Input Capacitance In c Output Capacitance out Notes: 1 ...
Page 4
... IS61C1024AL, IS64C1024AL IS61C1024AL/IS64C1024AL POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions I V Operating Supply Current I out I V Dynamic Operating Supply Current I out I TTL Standby Current (TTL Inputs) V CE1 ≥ V CE2 ≤ CMOS Standby Current (CMOS Inputs) CE1 ≥ V ce2 ≤ 0. Note address and data inputs are cycling at the maximum frequency means no input lines change ...
Page 5
... IS61C1024AL, IS64C1024AL READ CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Read Cycle Time rc t Address Access Time aa t Output Hold Time oha t CE1 Access Time 1 ace t CE2 Access Time 2 ace t OE Access Time Doe t ( Low-Z Output lzoe t ( High-Z Output hzoe t CE1 to Low-Z Output (2) 1 lzce t CE2 to Low-Z Output (2) 2 lzce t CE1 or CE2 to High-Z Output (2) hzce t (3) CE1 or CE2 to Power-Up ...
Page 6
... IS61C1024AL, IS64C1024AL AC WAVEFORMS READ CYCLE NO. 1 (1,2) ADDRESS D OUT PREVIOUS DATA VALID READ CYCLE NO. 2 (1,3) ADDRESS OE CE1 CE2 t LZCE1 t LZCE2 HIGH-Z D OUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE1 = V 3. Address is valid prior to or coincident with CE1 LOW and CE2 HIGH transitions OHA DOE t LZOE t ACE1 ...
Page 7
... IS61C1024AL, IS64C1024AL WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time wc t CE1 to Write End 1 sce t CE2 to Write End 2 sce t Address Setup Time to Write End aw t Address Hold from Write End ha t Address Setup Time Pulse Width (3) Pwe t Data Setup to Write End sD t Data Hold from Write End hD t (4) WE LOW to High-Z Output hzwe t WE HIGH to Low-Z Output (4) lzwe Notes: 1. Test conditions assume signal transition times less, timing reference levels of 1.5V, input pulse levels 3.0V and output loading specified in Figure 1 ...
Page 8
... IS61C1024AL, IS64C1024AL AC WAVEFORMS WRITE CYCLE NO. 1 (CE1 Controlled HIGH or LOW) ADDRESS t SA CE1 CE2 WE D DATA UNDEFINED OUT D IN WRITE CYCLE NO. 2 (OE is HIGH During Write Cycle) ADDRESS OE CE1 LOW HIGH CE2 DATA UNDEFINED OUT D IN Notes: 1. The internal write time is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write ...
Page 9
... IS61C1024AL, IS64C1024AL WRITE CYCLE NO. 3 (OE is LOW During Write Cycle) ADDRESS OE LOW CE1 LOW HIGH CE2 DATA UNDEFINED OUT D IN Integrated Silicon Solution, Inc. — www.issi.com — Rev. D 05/09/2012 ( VALID ADDRESS PWE2 t t HZWE HIGH DATA VALID IN 1-800-379-4774 t HA LZWE CE2_WR3 ...
Page 10
... IS61C1024AL, IS64C1024AL DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter V V for Data Retention Data Retention Current Dr t Data Retention Setup Time See Data Retention Waveform sDr t Recovery Time rDr Note: 1. Typical Values are measured 5V DATA RETENTION WAVEFORM (CE1 Controlled) VDD 4.5V 2. CE1 GND DATA RETENTION WAVEFORM (CE2 Controlled) VDD 4.5V CE2 2. 0.4V GND 10 Test Condition ...
Page 11
... IS61C1024AL, IS64C1024AL ORDERING INFORMATION: IS61C1024AL Commercial Range: 0°C to +70°C Speed (ns) Order Part No. 12 IS61C1024AL-12T ORDERING INFORMATION: IS61C1024AL Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 12 IS61C1024AL-12JLI IS61C1024AL-12KI IS61C1024AL-12KLI IS61C1024AL-12HI IS61C1024AL-12HLI IS61C1024AL-12TI IS61C1024AL-12TLI ORDERING INFORMATION: IS64C1024AL Automotive Range: –40°C to +125°C Speed (ns) Order Part No ...
Page 12
... IS61C1024AL, IS64C1024AL 12 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 05/09/2012 ...
Page 13
... IS61C1024AL, IS64C1024AL Integrated Silicon Solution, Inc. — www.issi.com — Rev. D 05/09/2012 1-800-379-4774 13 ...
Page 14
... IS61C1024AL, IS64C1024AL 14 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 05/09/2012 ...
Page 15
... IS61C1024AL, IS64C1024AL Integrated Silicon Solution, Inc. — www.issi.com — Rev. D 05/09/2012 1-800-379-4774 15 ...