BR93L86-W Rohm Semiconductor, BR93L86-W Datasheet - Page 13

• Manufacturer Part Number: BR93L86-W
• Description: IC EEPROM 16KBIT 2MHZ 8DIP
• Manufacturer: Rohm Semiconductor

Specifications of BR93L86-W

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 16K (1K x 16)
• Speed: 2MHz
• Interface: Microwire, 3-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

© 2011 ROHM Co., Ltd. All rights reserved.
BR93L□□-W Series, 93A□□-WM Series, BR93H□□-WC Series
www.rohm.com
4) Write enable (WEN) / disable (WDS) cycle
○ At power on, this IC is in write disable status by the internal RESET circuit. Before executing the write command, it is
○ When the write enable command is executed after power on, write enable status gets in. When the write disable command
5) Erase cycle timing (ERASE)
○In this command, data of the designated address is made into “1”. The data of the designated address becomes “FFFFh”.
6) Chip erase cycle timing (ERAL)
○In this command, data of all addresses is erased. Data of all addresses becomes ”FFFFh”.
Actual ERASE starts at the fall of CS after the fall of A0 taken SK clock.
In ERASE, status can be detected in the same manner as in WRITE command.
Actual ERASE starts at the fall of CS after the falll of the n-th clock from the start bit input.
In ERAL, status can be detected in the same manner as in WRITE command.
necessary to execute the write enable command. And, once this command is executed, it is valid unitl the write disable
command is executed or the power is turned off. However, the read command is valid irrespective of write enable / diable
command. Input to SK after 6 clocks of this command is available by either “H” or “L”, but be sure to input it.
is executed then, the IC gets in write disable status as same as at power on, and then the write command is canceled
thereafter in software manner. However, the read command is executable. In write enable status, even when the write
command is input by mistake, write is started. To prevent such a mistake, it is recommended to execute the write disable
command after completion of write.
CS
SK
DI
DO
CS
SK
DI
DO
CS
SK
DI
DO
High-Z
High-Z
High-Z
1
1
1
1
Fig.63 Write enable (WEN) / disable (WDS) cycle
Fig.64 Erase cycle timing
Fig.65 Chip erase cycle timing
1
1
1
2
0
2
1
0
0
2
Am
0
1
3
4
4
4
0
～ ～
～ ～
～ ～
～ ～
～ ～
A3
5
DISABLE=0 0
ENABLE=1 1
A2
6
A1
7
～ ～
A0
～ ～
8
tCS
n
13/40
tCS
n
～ ～
～ ～
～ ～
～ ～
n
tE/W
tE/W
BUSY
tSV
BUSY
～ ～
～ ～
～ ～
～ ～
～ ～
STATUS
～ ～
～ ～
～ ～
tSV
～ ～
～ ～
STATUS
READY
READY
～ ～
～ ～
～ ～
～ ～
～ ～
～ ～
～ ～
～ ～
～ ～
～ ～
BR93L46-Ｗ/A46-WM : n=9
BR93L56-W/A56-WM
BR93L66-W/A66-WM
BR93L76-W/A76-WM
BR93L86-W/A86-WM
BR93L46-W/A46-WM : n=9, m=5
BR93L56-W/A56-WM
BR93L66-W/A66-WM
BR93L76-W/A76-WM
BR93L86-W/A86-WM
BR93L46-W/A46-WM : n=9
BR93L56-W/A56-WM
BR93L66-W/A66-WM
BR93L76-W/A76-WM
BR93L86-W/A86-WM
: n=11
: n=13
Technical Note
2011.02 - Rev.F
: n=11, m=7
: n=13, m=9
: n=11
: n=13