E981.03A38HB ELMOS Semiconductor, E981.03A38HB Datasheet - Page 37

• Manufacturer Part Number: E981.03A38HB
• Description: Interface - Specialized KNX/EIB transceiver
• Manufacturer: ELMOS Semiconductor

Specifications of E981.03A38HB

• Rohs: yes
• Product Type: KNX/EIB Transceiver
• Operating Supply Voltage: 3.3 V
• Supply Current: 10 mA
• Maximum Power Dissipation: 1 W
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-32
• Minimum Operating Temperature: - 25 C

Table 25. Power supply registers
Table 26. Power supply control register
1) The bits VCC_ON and V20_ON are doubled for safety reasons. VCC and V20 supplies are switched off only if both ON bits have
2) Access via UART service and SPI possible. In case of hard or soft reset the register is reset to the hard reset value or soft reset
ELMOS Semiconductor AG reserves the right to change the detail specifications as may be required to permit improvements in the design of its products.
ALARM_STAT
bit description
Register Name
PS_CTRL
PS_STAT
PS_CTRL
content
hard reset value
soft reset value
external access
bit description
KNX/ EIB TRANSCEIVER
PRODUCTION DATA - JUL 2, 2012
ELMOS Semiconductor AG
value "0". Otherwise the supply is switched on and the ON bits are set to value "1" by the E981.03 itself.
value respectively.
MSB
PEND :
"1": an alarm transmission is either pending, under transmission or sent
(e.g. in case of alarm pin activation during transmission of a "normal" telegram)
"0": no alarm is pending or sent
Writing to the register using UART U_WriteReg service clears the PEND bit independent of
the value that is written to that bit.
Writing using SPI shall not change the value of the PEND bit which is not controlled by the
E981.03 but is in the responsibility of the host controller.
BUF :
"1": the alarm buffer was written completely
"0": the alarm buffer was not written completely yet
The bit is set by the E981.03 after successful upload using host UART interface services.
It may be written by the host directly to activate alarm functionality without using upload
procedure via host UART interface or after uploading a alarm telegramm by SPI. The alarm
telegram buffer is not checked for correctness in this case.
SENT :
"1": an alarm telegram was sent
"0": no alarm telegram was sent
The bit is set after sending of an alarm telegram.
It can be reset by the host processor by writing a "0". The host should never write an “1” to
the SENT bit. If the bit SENT is set no alarm telegram is transmitted regardless of the alarm
condition. An ongoing alarm telegram transmission on EIB bus (states AlarmTelegramWait
and AlarmTelegramTransmit) is not interrupted by writing a “0” to the SENT bit.
A reading by UART Interface delete this bit. A SPI read do not delete this and the User have
to do this.
MSB
VIO_SW
0
0
R/W
VCC_ON :
“00”: VCC is to switch off
“01”,”10”,”11”: V
The bits do not reflect the state of the V
The actual state is reflected by PS_STAT register.
V20_ON :
"00": V
“01”,”10”,”11”: V
The bits do not reflect the state of the V
The actual state is reflected by PS_STAT register.
VIO_SW:
When VCC = 5 V and VIO = 3.3 V: write “1” to VIO_SW bit to reduce power consumption of
E981.03. In all other cases this bit has no effect.
Address
0x20E
0x3BF
2)
20
is to switch off
-
0
-
R
CC
20
Description
power supply control register
power supply status register
is to switch on
is to switch on
VCC_ON1
1
1
R/W
1)
1)
2)
Data Sheet
37/51
1)
VCC_ON0
1
1
R/W
CC
20
2)
supply.
supply.
1)
-
0
-
R
-
0
-
R
back to
V20_ON1
1
1
R/W
QM-No.: 25DS0046E.01
Table 8 Register Table
2)
1)
E981.03
LSB
V20_ON0
1
1
R/W
LSB
2)
1)