1893AFILFT IDT, 1893AFILFT Datasheet - Page 26
1893AFILFT
Manufacturer Part Number
1893AFILFT
Description
Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
Manufacturer
IDT
Datasheet
1.1893AFLF.pdf
(136 pages)
Specifications of 1893AFILFT
Rohs
yes
Part # Aliases
ICS1893AFILFT
- Current page: 26 of 136
- Download datasheet (963Kb)
6.2 Serial Management Interface
6.3 Twisted-Pair Interface
ICS1893AF, Rev D 10/26/04
The ICS1893AF provides an ISO/IEC compliant, two-wire Serial Management Interface as part of its
MAC/Repeater Interface. This Serial Management Interface is used to exchange control, status, and
configuration information between a Station Management entity (STA) and the physical layer device (PHY),
that is, the ICS1893AF.
The ISO/IEC standard also specifies a frame structure and protocol for this interface as well as a set of
Management Registers that provide the STA with access to a PHY such as the ICS1893AF. A Serial
Management Interface is comprised of two signals: a bi-directional data pin (MDIO) along with an
associated input pin for a clock (MDC). The clock is used to synchronize all data transfers between the
ICS1893AF and the STA.
In addition to the ISO/IEC defined registers, the ICS1893AF provides several extended status and control
registers to provide more refined control of the MII and MDI interfaces. For example, the QuickPoll Detailed
Status Register provides the ability to acquire the most-important status functions with a single MDIO read.
Note:
For the twisted-pair interface, the ICS1893AF uses 1:1 ratio transformers for both transmit and receive.
Better operation results from using a split ground plane through the transformer. In this case:
•
•
•
The RJ-45 transformer windings must be on the chassis ground plane along with the Bob Smith
termination.
The ICS1893AF system ground plane must include the ICS1893AF-side transformer windings along with
the 61.9
The transformer provides the isolation with one set of windings on one ground plane and another set of
windings on the second ground plane.
ICS1893AF Data Sheet - Release
In the ICS1893AF, the MDIO and MDC pins remain active for all the MAC/Repeater Interface
modes (that is, 10M MII, 100M MII, 100M Symbol, and 10M Serial).
resistors and the 120-nH inductor.
Copyright © 2004, Integrated Circuit Systems, Inc.
All rights reserved.
26
Chapter 6 Interface Overviews
October, 2004
Related parts for 1893AFILFT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
#1893 LAMP T-3 1/4 14V 330MA MINIATURE BAYONET BASE
Manufacturer:
EIKO
Part Number:
Description:
LAMP, INCANDESCENT, BAYONET, 14V
Manufacturer:
CHICAGO MINIATURE LIGHTING, LLC
Datasheet:
Part Number:
Description:
IDT TS3000AND TSE2002 SENSORS SAMPLE PACK OFFER
Manufacturer:
Integrated Device Technology (Idt)
Part Number:
Description:
THERMOCOUPLE DIGITAL PANEL METER
Manufacturer:
NEWPORT ELECTRONICS
Part Number:
Description:
High-performance CMOS bus interface latches
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Accessories Connectors and Cables
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Accessories 5.25 Industrial Disk Tray
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
IDT PART
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet: