DS1086Z-11D Maxim Integrated, DS1086Z-11D Datasheet
DS1086Z-11D
Specifications of DS1086Z-11D
Related parts for DS1086Z-11D
DS1086Z-11D Summary of contents
Page 1
... Nonvolatile Settings o 5V Supply o No External Timing Components Required o Power-Down Mode o 10kHz Master Frequency Step Size o EMI Reduction PART DS1086U DS1086U+ DS1086Z DS1086Z+ Note: Contact the factory for custom settings. + Denotes a lead(Pb)-free/RoHS-compliant package. TOP VIEW V CC SCL* SDA* PDN OE Features ...
Page 2
Spread-Spectrum EconOscillator ABSOLUTE MAXIMUM RATINGS Voltage on V Relative to Ground ......................-0.5V to +6.0V CC Voltage on SPRD, PDN, OE, SDA, SCL Relative to Ground (See Note 1).......-0 Continuous Power Dissipation (T = +70°C) A µSOP (derate 4.5mW/°C ...
Page 3
MASTER OSCILLATOR CHARACTERISTICS ( ±5 0°C to +70°C PARAMETER SYMBOL Master Oscillator Range Default Master Oscillator Frequency Master Oscillator Frequency Tolerance Voltage Frequency Variation Temperature Frequency Variation Dither Frequency Range Integral Nonlinearity of Frequency ...
Page 4
Spread-Spectrum EconOscillator AC ELECTRICAL CHARACTERISTICS ( ±5 0°C to +70°C PARAMETER SYMBOL Frequency Stable After Prescaler Change Frequency Stable After DAC or Offset Change Power-Up Time t por Enable of OUT After Exiting t ...
Page 5
AC ELECTRICAL CHARACTERISTICS: 2-WIRE INTERFACE (continued ±5 0°C to +70°C PARAMETER SYMBOL Setup Time for STOP t Capacitive Load for Each Bus Line NV Write-Cycle Time Input Capacitance Note 1: All voltages are ...
Page 6
Spread-Spectrum EconOscillator (V = 5.0V unless otherwise noted) ° SUPPLY CURRENT vs. TEMPERATURE TEMPERATURE (°C) ...
Page 7
PIN NAME 1 OUT Oscillator Output 2 SPRD Dither Enable. When the pin is high, the dither is enabled. When the pin is low, the dither is disabled Power Supply CC 4 GND Ground Output Enable. When the ...
Page 8
Spread-Spectrum EconOscillator Table 1. Register Summary REGISTER ADDR MSB PRESCALER 02h DAC HIGH 08h b9 b8 DAC LOW 09h b1 b0 OFFSET 0Eh ADDR 0Dh RANGE 37h X ...
Page 9
V CC SDA SCL PDN OE SPRD GND Figure 3. DS1086 Block Diagram The output frequency is determined by the following equation: ( MIN FREQUENCY OF SELECTED OFFSET RANGE + × DAC VALUE f = OUTPUT PRESCALER where: ...
Page 10
Spread-Spectrum EconOscillator The A0, A1, A2 bits determine the 2-wire slave address. The WC bit determines if the EEPROM written to after register contents have been changed (default), EEPROM is written automatically after ...
Page 11
RANGE register (last five bits). In this example, 12h (18 decimal) was read from the RANGE register for this case is 10h (16 deci- mal). This is the value that is written ...
Page 12
Spread-Spectrum EconOscillator MSB DEVICE DEVICE IDENTIFIER ADDRESS Figure 5. Slave Address SDA t BUF t LOW SCL t HD:STA STOP START Figure 6. 2-Wire AC Characteristics Since the expected output frequency is equal to the ...
Page 13
Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred between START and STOP con- ditions is not limited, and is determined by the master device. The information is ...
Page 14
Spread-Spectrum EconOscillator TYPICAL 2-WIRE WRITE TRANSACTION MSB LSB START A2* A1* A0* R/W DEVICE READ/ DEVICE IDENTIFIER ADDRESS WRITE EXAMPLE 2-WIRE TRANSACTIONS (WHEN A0, A1, AND A2 ARE ZERO) B0h A) SINGLE BYTE WRITE START 1 ...
Page 15
... Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 15 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2012 Maxim Integrated Products ...