HFCT-5964ATG NEL [Nel Frequency Controls,inc], HFCT-5964ATG Datasheet - Page 11

• Manufacturer Part Number: HFCT-5964ATG
• Description: ATG Single Mode Laser Small Form Factor Transceivers for ATM, SONET OC-3 /SDH STM-1 Part of the Agilent METRAK family
• Manufacturer: NEL [Nel Frequency Controls,inc]

Regulatory Compliance
The Regulatory Compliance for
transceiver performance is
shown in Table 1. The overall
equipment design will determine
the certification level. The
transceiver performance is
offered as a figure of merit to
assist the designer in
considering their use in
equipment designs.
Electrostatic Discharge (ESD)
There are two design cases in
which immunity to ESD damage
is important.
The first case is during handling
of the transceiver prior to
mounting it on the circuit board.
It is important to use normal
ESD handling precautions for
ESD sensitive devices. These
precautions include using
grounded wrist straps, work
benches, and floor mats in ESD
controlled areas.
Table 1: Regulatory Compliance - Targeted Specification
11
Feature
Electrostatic Discharge (ESD)
Electrical Pins
Electrostatic Discharge (ESD)
Electromagnetic Interference
(EMI)
Immunity
Laser Eye Safety
and Equipment Type Testing
Component
Recognition
to the
to the LC Receptacle
MIL-STD-883
Method 3015
FCC Class B
FDA CDRH 21-CFR 1040
Class 1
IEC 60825-1
Underwriters Laboratories and Canadian
Recognition
Including Electrical Business Equipment.
Test Method
Variation of IEC 61000-4-2
Variation of IEC 61000-4-3
Amendment 2 2001-01
Standards Association Joint Component
for Information Technology Equipment
The second case to consider is
static discharges to the exterior
of the equipment chassis
containing the transceiver parts.
To the extent that the LC
connector receptacle is exposed
to the outside of the equipment
chassis it may be subject to
whatever system-level ESD test
criteria that the equipment is
intended to meet.
Electromagnetic Interference (EMI)
Most equipment designs utilizing
these high-speed transceivers
from Agilent will be required to
meet FCC regulations in the
United States, CENELEC
EN55022 (CISPR 22) in Europe
and VCCI in Japan. Refer to EMI
section (page 9) for more details.
Immunity
Transceivers will be subject to
radio-frequency electromagnetic
fields following the IEC 61000-4-3
test method.
Performance
Class 1 (>500 V).
Margins are dependent on customer board and chassis designs.
10 V/m field swept from 27 to 1000 MHz applied to the transceiver
License Number:
UL File Number: E173874, 01SC14051
Tested to 8 kV contact discharge.
Typically show no measurable effect from a
without a chassis enclosure.
Accession Number:
Eye Safety
These laser-based transceivers
are classified as AEL Class I
(U.S. 21 CFR(J) and AEL Class 1
per EN 60825-1 (+A11). They are
eye safe when used within the
data sheet limits per CDRH.
They are also eye safe under
normal operating conditions and
under all reasonably foreseeable
single fault conditions per
EN60825-1. Agilent has tested
the transceiver design for
compliance with the
requirements listed below under
normal operating conditions and
under single fault conditions
where applicable. TUV
Rheinland has granted
certification to these
transceivers for laser eye safety
and use in EN 60825-2
applications. Their performance
enables the transceivers to be
used without concern for eye
safety up to 3.5 V transmitter
V
CC
QFCT-5987TL ) 933/510201/02 18 Jan. 2002
.
QFCT-5987TL ) 9521220-47