AT52SC1283J-70CI ATMEL [ATMEL Corporation], AT52SC1283J-70CI Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
AT52SC1283J-70CI
Manufacturer Part Number
AT52SC1283J-70CI
Description
128-Mbit Flash + 32-Mbit/64-Mbit
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT52SC1283J-70CI.pdf
(52 pages)
6.4
6.5
6.6
3530B–STKD–2/4/05
Page Read
Synchronous Reads
Continuous Burst Read
the device. The access time is measured from stable address, falling edge of AVD or falling
edge of CE, whichever occurs last. During the AVD pulsed read, the CLK signal may be static
high or static low. For standard asynchronous reads, the AVD and CLK signal should be tied to
GND. The asynchronous read diagrams are shown on
The page read operation of the device is controlled by CE, OE, and AVD inputs. The CLK input
is ignored during a page read operation and should be tied to GND. The page size is four words.
During a page read, the AVD signal can transition low and then transition high, transition low and
remain low, or can be tied to GND. If a high to low transition on the AVD signal occurs, as shown
in Page Read Cycle Waveform 1, the page address is latched by the low-to-high transition of the
AVD signal. However, if the AVD signal remains low after the high-to-low transition or if the AVD
signal is tied to GND, as shown in Page Read Cycle Waveform 2, then the page address (A22 -
A2) cannot change during a page read operation. The first word access of the page read is the
same as the asynchronous read. The first word is read at an asynchronous speed of 70 ns.
Once the first word is read, toggling A0 and A1 will result in subsequent reads within the page
being output at a speed of 20 ns. If the AVD and the CLK pins are both tied to GND, the device
will behave like a standard asynchronous Flash memory. The page read diagrams are shown on
page
Synchronous reads are used to achieve a faster data rate that is possible in the asynchro-
nous/page read mode. The device can be configured for continuous or fixed-length burst
access. The burst read operation of the device is controlled by CE, OE, CLK and AVD inputs.
The initial read location is determined as for the AVD pulsed asynchronous read operation; it can
be any memory location in the device. In the burst access, the address is latched on the rising
edge of the first clock pulse when AVD is low or the rising edge of the AVD signal, whichever
occurs first. The CLK input signal controls the flow of data from the device for a burst operation.
After the clock latency cycles, the data at the next burst address location is read for each follow-
ing clock cycle.
Figure 6-1.
During a continuous burst read, any number of addresses can be read from the memory. When
operating in the linear burst read mode (B7 = 1) with the burst wrap bit (B3 = 1) set, the device
may incur an output delay when the burst sequence crosses the first 16-word boundary in the
memory (see
address is D13 - D15, an output delay equal to the initial clock latency is incurred. The delay
23.
D0 D1
Word D0 - D3
Figure
Word Boundary
D2
6-1). If the starting address is D0 - D12, there is no delay. If the starting
D3 D4
Word D4 - D7
AT52SC1283J/1284J [Preliminary]
D5
D6 D7 D8 D9 D10 D11 D12 D13 D14 D15
Word D8 - D11
page
30.
Word D12 - D15
16-word Boundary
5