S71GL064A08 SPANSION [SPANSION], S71GL064A08 Datasheet - Page 54

• Manufacturer Part Number: S71GL064A08
• Description: STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
• Manufacturer: SPANSION [SPANSION]

52
Read (Note 6)
Reset (Note 7)
Enter Secured Silicon Sector Region
Exit Secured Silicon Sector Region
Program
Write to Buffer (Note 11)
Program Buffer to Flash
Write to Buffer Abort Reset (Note 13)
Unlock Bypass
Unlock Bypass Program (Note 14)
Unlock Bypass Reset (Note 15)
Chip Erase
Sector Erase
Program/Erase Suspend (Note 16)
Program/Erase Resume (Note 17)
CFI Query (Note 18)
Legend:
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on falling edge of WE# or
CE# pulse, whichever happens later.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
If WP# protects highest address sector, data is 98h for factory
See
All values are in hexadecimal.
Shaded cells indicate read cycles. All others are write cycles.
During unlock and command cycles, when lower address bits are
555 or 2AA as shown in table, address bits above A11 and data
bits above DQ7 are don’t care.
No unlock or command cycles required when device is in read
mode.
Reset command is required to return to read mode (or to erase-
suspend-read mode if previously in Erase Suspend) when device
is in autoselect mode, or if DQ5 goes high while device is
providing status information.
Fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. Except for RD, PD
and WC. See
information.
Device ID must be read in three cycles.
locked and 18h for not factory locked. If WP# protects lowest
address sector, data is 88h for factory locked and 08h for not
factor locked.
Manufacturer ID
Device ID (Note 9)
Secured Silicon Sector Factory
Protect (Note 10)
Sector Group Protect Verify (Note
12)
Table 1
Command Definitions
Command
Sequence
(Note 1)
for description of bus operations.
Autoselect Command Sequence
Table 10. Command Definitions (x16 Mode, BYTE# = V
1
1
4
4
4
4
3
4
4
3
1
3
3
2
2
6
6
1
1
1
Addr
XXX
XXX
XXX
XXX
XXX
555
555
555
555
555
555
555
555
555
555
555
555
RA
SA
55
First
section for more
Data
RD
AA
AA
AA
AA
AA
AA
AA
AA
29
AA
AA
A0
90
AA
AA
B0
30
98
F0
A d v a n c e
S71GL064A based MCPs
Addr
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
XXX
2AA
2AA
PA
Second
Data
PD
55
55
55
55
55
55
55
55
55
55
00
55
55
PD = Program Data for location PA. Data latches on rising edge of
WE# or CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write
buffer page as PA.
WC = Word Count. Number of write buffer locations to load minus 1.
10. Data is 00h for an unprotected sector group and 01h for a
11. Total number of cycles in command sequence is determined by
12. Command sequence resets device for next command after
13. Unlock Bypass command is required prior to Unlock Bypass
14. Unlock Bypass Reset command is required to return to read
15. System may read and program in non-erasing sectors, or enter
16. Erase Resume command is valid only during Erase Suspend
17. Command is valid when device is ready to read array data or
18. Refer to Table 4, AutoSelect Codes for individual Device IDs per
Addr
555
555
555
555
555
555
555
555
555
555
555
SA
I n f o r m a t i o n
protected sector group.
number of words written to write buffer. Maximum number of
cycles in command sequence is 21, including “Program Buffer to
Flash” command.
aborted write-to-buffer operation.
Program command.
mode when device is in unlock bypass mode.
autoselect mode, when in Erase Suspend mode. Erase Suspend
command is valid only during a sector erase operation.
mode.
when device is in autoselect mode.
device density and model number.
Third
Bus Cycles (Notes 2–5)
Data
90
90
90
90
88
90
A0
25
20
80
80
F0
(SA)X02
Addr
XXX
X00
X01
X03
555
555
SA
PA
Fourth
(Note 10)
00/01
0001
227E
Data
WC
00
PD
AA
AA
IH
)
S71GL064A_00_A2 February 8, 2005
Addr
X0E
2AA
2AA
PA
Fifth
(Note
Data
18)
PD
55
55
Addr
WBL
555
X0F
SA
Sixth
(Note
Data
18)
PD
10
30