S71GL064A08 SPANSION [SPANSION], S71GL064A08 Datasheet - Page 48
S71GL064A08
Manufacturer Part Number
S71GL064A08
Description
STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S71GL064A08.pdf
(134 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
S71GL064A08BFW0B0
Manufacturer:
spansion
Quantity:
6 249
- Current page: 48 of 134
- Download datasheet (3Mb)
46
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or
a Write to Buffer programming operation so that data can be read from any non-suspended
sector. When the Program Suspend command is written during a programming process, the
device halts the program operation within 15 µs maximum (5µs typical) and updates the sta-
tus bits. Addresses are not required when writing the Program Suspend command.
After the programming operation has been suspended, the system can read array data from
any non-suspended sector. The Program Suspend command may also be issued during a pro-
gramming operation while an erase is suspended. In this case, data may be read from any
addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured
Silicon Sector area (One-time Program area), then user must use the proper command se-
quences to enter and exit this region. Note that the Secured Silicon Sector, autoselect, and
CFI functions are unavailable when a program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Pro-
gram Suspend mode. The system can read as many autoselect codes as required. When the
device exits the autoselect mode, the device reverts to the Program Suspend mode, and is
ready for another valid operation. See Autoselect Command Sequence for more information.
After the Program Resume command is written, the device reverts to programming. The sys-
tem can determine the status of the program operation using the DQ7 or DQ6 status bits, just
as in the standard program operation. See Write Operation Status for more information.
Note:See
Increment Address
Figure 4. Program Operation
Table 10
A d v a n c e
Embedded
in progress
S71GL064A based MCPs
algorithm
Program
for program command sequence.
No
Command Sequence
I n f o r m a t i o n
Write Program
Last Address?
Programming
from System
Verify Data?
Completed
Data Poll
START
Yes
Yes
No
S71GL064A_00_A2 February 8, 2005
Related parts for S71GL064A08
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: