X4003 Xicor, X4003 Datasheet - Page 10

• Manufacturer Part Number: X4003
• Description: CPU Supervisor
• Manufacturer: Xicor

X4003/X4005
ABSOLUTE MAXIMUM RATINGS
Temperature under bias ................... -65°C to +135°C
Storage temperature ........................ -65°C to +150°C
Voltage on any pin with
D.C. output current ............................................... 5mA
Lead temperature (soldering, 10 seconds).........300°C
RECOMMENDED OPERATING CONDITIONS
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) The device enters the active state after any start, and remains active until: 9 clock cycles later if the device select bits in the slave
REV 1.1.3 4/30/02
Symbol
respect to V
Temperature
I
I
I
I
V
I
V
CC2
CC3
CC4
CC5
V
Commercial
CC
V
I
HYS
I
IH
LO
IL
Industrial
OL
LI
(3)
(1)
(3)
(1)
(2)
(2)
(2)
(2) The device goes into standby: 200ns after any stop, except those that initiate a nonvolatile write cycle; t
(3) V
address byte are incorrect; 200ns after a stop ending a read operation; or t
a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct device select bits in the slave address byte.
IL
Active supply current
read control register
Active supply current
write control register
Operating current AC
(WDT off)
Operating current DC
(WDT off)
Operating current DC
(WDT on)
Input leakage current
Output leakage current
Input LOW voltage
Input HIGH voltage
Schmitt trigger input
hysteresis fixed input level
V
Output LOW voltage
min. and V
CC
SS
related level
.......................................-1.0V to +7V
Parameter
IH
max. are for reference only and are not tested.
-40°C
Min.
0°C
V
.05 x V
V
CC
CC
Min
-0.5
0.2
+85°C
Max.
70°C
x 0.7 V
= 1.8 to 3.6V
CC
www.xicor.com
V
CC
CC
Max
0.5
1.5
0.4
10
10
10
1
1
+ 0.5 V
x 0.3
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of
the device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
.05 x V
V
CC
Blank and –4.5A
CC
Min
-0.5
–2.7 and –2.7A
0.2
x 0.7 V
= 2.7 to 5.5V
Option
CC
WC
–1.8
after a stop ending a write operation.
V
CC
CC
Max
1.0
3.0
0.4
20
10
10
1
1
Characteristics subject to change without notice.
+ 0.5
x 0.3
Unit
mA
mA
µA
µA
µA
µA
µA
V
V
V
V
Supply Voltage Limits
f
400kHznonvolatile,
SDA = Open
V
Others = GND or V
V
V
Device is in Standby
I
I
SCL
OL
OL
SDA
IN
SDA
WC
1.8V to 3.6V
2.7V to 5.5V
4.5V to 5.5V
Test Conditions
= 3.0mA (2.7–5.5V)
= 1.8mA (1.8–3.6V)
= GND to V
after a stop that initiates
=
= V
= GND to V
SCL
= V
CC
CC
CC
10 of 18
SB
(2)