OX16PCI954-TQC60-A OXFORD [Oxford Semiconductor], OX16PCI954-TQC60-A Datasheet - Page 23
![no-image](/images/no-image-200.jpg)
OX16PCI954-TQC60-A
Manufacturer Part Number
OX16PCI954-TQC60-A
Description
Integrated Quad UART and PCI interface
Manufacturer
OXFORD [Oxford Semiconductor]
Datasheet
1.OX16PCI954-TQC60-A.pdf
(72 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
OX16PCI954-TQC60-A1
Manufacturer:
AD
Quantity:
556
LT2[15:0] enable the card designer to control the data bus during the idle periods. The default values will configure the Local Bus
data pins to remain forcing (LT2[7:4] = Fh). LT[15:8] is programmed to place the bus in high-impedance at the beginning of a
read cycle and set it back to forcing at the end of the read cycle. For systems that require the data bus to stay in high-
impedance, the card designer should write an appropriate value in the range of 0h to Ah to LT2[7:4]. This will place the data bus
in high impedance at the end of the write cycle. Whenever the value programmed in LT2[7:4] does not equal Fh, the Local Bus
controller will ignore the setting of LT2[15:8] as the data bus will be high-impedance outside write cycles. In this case the card
designer should place external pull-ups on the data bus pins LBD[7:0] (or LBD[32:0] in 32-bit mode).
While the configuration data is read from the external EEPROM, the LBD pins remain in the high-impedance state.
The timing registers define the Local Bus timing parameters based on signal changes relative to a reference cycle which is
defined as two PCI clock cycles after IRDY# is asserted for the first time in a frame. The following parameters are fixed relative to
the reference cycle.
The Local Bus address pins (LBA[7:0] in 8-bit Local Bus, LBA[15:0] in 32-bit Local Bus) are asserted during the reference cycle.
In a write operation, the Local Bus data is available during the reference cycle, however I/O buffers change direction as
programmed in LT2[3:0].
In a Motorola type bus write operation, the Read-not-Write pin (LBRDWR#) is asserted (low) during the reference cycle. In a read
cycle this pin remains high throughout the duration of the operation.
The default settings in LT1 & LT2 registers provide one PCI clock cycle for address and chip-select to control signal set-up time,
one clock cycle for address and chip-select from control signal hold time, two clock cycles of pulse duration for read and write
control signals and one clock cycle for data bus hold time. These parameters are acceptable for using external OX16C950,
OX16C952 and OX16C954 devices connected to the Local Bus, in Intel mode. Some redefinition will be required if the bus is to
be operated in Motorola mode.
The user should take great care when programming the Local Bus timing parameters. For example defining a value for chip-
select assertion which is larger that the value defined for chip-select de-assertion or defining a chip-select assertion value which
is greater than control signal assertion will result in obvious invalid local Bus cycles.
6.4.5
The receiver FIFO level of all internal UARTs are shadowed in Local configuration registers as follows:
6.4.6
The transmitter FIFO level of all internal UARTs are shadowed in Local configuration registers as follows:
Data Sheet Revision 1.3
Bits
7:0
15:8
23:16
31:24
Bits
7:0
15:8
23:16
31:24
OXFORD SEMICONDUCTOR LTD.
UART Receiver FIFO Levels ‘URL’ (Offset 0x10)
UART Transmitter FIFO Levels ‘UTL’ (Offset 0x14)
Description
UART0 Transmitter FIFO Level (TFL[7:0])
UART1 Transmitter FIFO Level (TFL[7:0])
UART2 Transmitter FIFO Level (TFL[7:0])
UART3 Transmitter FIFO Level (TFL[7:0])
Description
UART0 Receiver FIFO Level (RFL[7:0])
UART1 Receiver FIFO Level (RFL[7:0])
UART2 Receiver FIFO Level (RFL[7:0])
UART3 Receiver FIFO Level (RFL[7:0])
Read/Write
EEPROM
Read/Write
EEPROM
-
-
-
-
-
-
-
-
PCI
PCI
R
R
R
R
R
R
R
R
OX16PCI954
Reset
Reset
0x00h
0x00h
0x00h
0x00h
0x00h
0x00h
0x00h
0x00h
Page 23