ZLF645 MAXIM [Maxim Integrated Products], ZLF645 Datasheet - Page 134

no-image

ZLF645

Manufacturer Part Number
ZLF645
Description
Flash MCUs with Learning Amplification
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ZLF645E0H2064G
Manufacturer:
Maxim
Quantity:
419
Part Number:
ZLF645E0H2864G
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
ZLF645E0H4864G
Manufacturer:
Maxim
Quantity:
468
Part Number:
ZLF645E0P2064G
Manufacturer:
Maxim
Quantity:
490
Part Number:
ZLF645E0P2864G
Manufacturer:
Maxim
Quantity:
420
Part Number:
ZLF645E0Q2064G
Manufacturer:
Maxim
Quantity:
28
Part Number:
ZLF645EDH2864G
Manufacturer:
HOLTEK/合泰
Quantity:
20 000
Part Number:
ZLF645EOH2864G
Manufacturer:
ZILOG
Quantity:
20 000
Part Number:
ZLF645EOS2864G
Manufacturer:
ZILOG
Quantity:
20 000
Table 59. Timer 8/Timer 16 Control Register (CTR3)
19-4572; Rev 0; 4/09
Bit
Field
Reset
R/W
Address
Bit Position
[7] 
[6]
[5]
[4]
[3] 
[2:0]
T16_Enable
Value
R/W
0
1
0
1
0
1
0
1
0
1
7
0
Description
T16_Enable —Disable/enable the T16 counter. (Note: This register bit
duplicates the function of register bit 7 of the CTR2 register).
Disables the T16 counter if bit 7 of the CTR2 register is also 0.
Enables the T16 counter if bit 7 of the CTR2 register is also 0 and has no effect
if the T16 counter is already enabled by bit 7of the CTR2 register being 1.
T8_Enable —Disable/enable the T8 counter. (Note: This register bit duplicates
the function of register bit 7of the CTR0 register).
Disables the T8 counter if bit 7of the CTR0 register is also 0.
Enables the T8 counter if bit 7of the CTR0 register is also 0 and has no effect if
the T8 counter is already enabled by bit 7of the CTR0 register being 1.
Sync_Mode —When enabled, the first pulse of Timer 8 (the carrier) is always
synchronized with Timer 16 (the demodulated signal). It can always provide a
full carrier pulse. This bit is not reset upon Stop Mode Recovery.
Disable SYNC mode.
Enable SYNC mode.
T16_Out Disable —Set this bit to disable toggling of the Timer 16 output. Time-
out interrupts are still generated. This bit is not reset upon Stop Mode Recovery.
T16 toggles normally.
T16 toggle is disabled.
T8 Demodulate —(Capture one cycle) This bit is not reset upon Stop Mode
Recovery.
T8 captures events normally.
T8 becomes active on the third edge, captures events on the fourth and fifth
edges, and generates an interrupt on the fifth edge. After a T8 time-out the
event count resets to 0 and the fourth and fifth edges are captured again.
Reserved —Always reads 111b. Must be written to 1.
T8_Enable
R/W
6
0
Sync_Mode
Bank D: 03h; Linear: D03h
R/W
5
0
T16_Out
Disable
R/W
4
0
Demodulate
ZLF645 Series Flash MCUs
R/W
T8
3
0
Product Specification
Counter/Timer Registers
X
2
Reserved
X
1
X
0
126

Related parts for ZLF645