UAA2080H PHILIPS [NXP Semiconductors], UAA2080H Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
UAA2080H
Manufacturer Part Number
UAA2080H
Description
Advanced pager receiver
Manufacturer
PHILIPS [NXP Semiconductors]
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UAA2080H
Manufacturer:
PHILIPS
Quantity:
18
Company:
Part Number:
UAA2080H
Manufacturer:
TXC
Quantity:
12 388
Part Number:
UAA2080H
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
TEST INFORMATION
Tuning procedure for AC tests
1. Turn on the signal generator: f
2. Measure the IF with a counter connected to test pin TPI. Tune C16 to set the crystal oscillator to achieve f
3. Set the signal generator to nominal frequency (f
4. Tune C15 (oscillator output circuit) and C12 (frequency multiplier output) to obtain a peak audio voltage on pin TPI.
5. Tune C3 and C6 (RF input and mixer input) to obtain a peak audio voltage on pin TPI. When testing the mixer input
6. Check that the output signal on pin TPQ is within 3 dB in amplitude and at 90 ( 20 ) relative phase of the signal on
7. Check that data signal appears on output pin DO and proceed with the AC test.
AC test conditions
Table 5 Definitions for AC test conditions (see Table 6)
1996 Jan 15
Modulated test signal 1
Frequency
Deviation
Modulation 1200 baud pseudo random bit sequence
Rise time
Modulated test signal 2
Deviation
Modulation 400 Hz sinewave
Other definitions
f
f
f
P
P
P
P
1
2
3
f
SIGNAL
1
2
3
i(ref)
Advanced pager receiver
cs
Change the generator frequency to f
frequency f
crystal frequency is f
signal must be used with f
Table 1).
wave modulation, V
receiver is tuned, to ensure V
sensitivity tune C23 instead of C3 and C6 (test circuit Fig.5).
pin TPI.
172.941, 469.950 or 930.500 MHz
250 25 s (between 10% and 90% of final value)
frequency of signal generator 1
frequency of signal generator 2
frequency of signal generator 3
channel spacing (20 kHz)
maximum available power from signal generator 1 at the test board input
maximum available power from signal generator 2 at the test board input
maximum available power from signal generator 3 at the test board input
maximum available power at the test board input to give a Bit Error Rate (BER)
test signal 1, in the absence of interfering signals and under the conditions as specified in Chapters
“AC characteristics (173 MHz)”, “AC characteristics (470 MHz)” and “AC characteristics (930 MHz)”
i(RF)
4.0 kHz
2.4 kHz
= 172.941 MHz the crystal frequency is f
i(RF)
XTAL
= 1 mV (RMS). Note that the RF signal should be reduced in the following tests, as the
= 78.325 MHz. For a received input frequency f
i(OSC)
o(IF)
gen
= 310.1667 MHz and a level of 15 dBm (for definition of crystal frequency, see
= 10 to 50 mV (p-p) on test pins TPI or TPQ.
= f
i(RF)
gen
= f
+ 4 kHz, no modulation, V
i(RF)
i(RF)
4 kHz and check that f
) and turn on the modulation deviation 4.0 kHz, 600 Hz square
25
DESCRIPTION
XTAL
= 57.647 MHz, while for f
i(RF)
IF
= 1 mV (RMS).
i(RF)
is also 4 kHz. For a received input
= 930.500 MHz an external oscillator
i(RF)
= 469.950 MHz the
3
100
Product specification
for the modulated
UAA2080
IF
= 4 kHz