UAA2080H PHILIPS [NXP Semiconductors], UAA2080H Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
UAA2080H
Manufacturer Part Number
UAA2080H
Description
Advanced pager receiver
Manufacturer
PHILIPS [NXP Semiconductors]
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UAA2080H
Manufacturer:
PHILIPS
Quantity:
18
Company:
Part Number:
UAA2080H
Manufacturer:
TXC
Quantity:
12 388
Part Number:
UAA2080H
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
FUNCTIONAL DESCRIPTION
The complete circuit consists of the following functional
blocks as shown in Figs 1 to 6.
Radio frequency amplifier
The RF amplifier is an emitter-coupled pair driving a
balanced cascode stage, which drives an external
balanced tuned circuit. Its bias current is set by an external
300
current the optimum source resistance is 1.3 k at VHF
and 1.0 k at UHF. At 930 MHz a higher bias current is
required to achieve optimum gain. A value of 120
used for R1, which corresponds with a bias current of
approximately 1.3 mA and an optimum source resistance
of approximately 600 .The capacitors C1 and C2
transform a 50
The output drives a tuned circuit with capacitive divider
(C7, C8 and C9) to provide maximum power transfer to the
phase-splitting network and the mixers.
Mixers
The double balanced mixers consist of common base
input stages and upper switching stages driven from the
frequency multiplier. The 300
mixer acts together with external components (C10, C11;
L4, L5 respectively) as phase shifter/power splitter to
provide a differential phase shift of 90 degrees between
the I channel and the Q channel. At 930 MHz all external
phase shifter components are inductive (L10, L11; L4, L5).
Oscillator
The oscillator is based on a transistor in common collector
configuration. It is followed by a cascode stage driving a
tuned circuit which provides the signal for the frequency
multiplier. The oscillator bias current (typically 250 A) is
determined by the 1.8 k external resistor R5.
The oscillator frequency is controlled by an external 3rd
overtone crystal in parallel resonance mode. External
capacitors between base and emitter (C17) and from
emitter to ground (C16) make the oscillator transistor
appear as having a negative resistance for small signals;
this causes the oscillator to start. Inductance L9 connected
in parallel with capacitor C16 to the emitter of the oscillator
transistor prevents oscillation at the fundamental
frequency of the crystal.
1996 Jan 15
Advanced pager receiver
resistor R1 to typically 770 A. With this bias
source resistance to this optimum value.
input impedance of each
is
19
The resonant circuit at output pin OSC selects the second
harmonic of the oscillator frequency. In other applications
a different multiplication factor may be chosen.
At 930 MHz an external oscillator circuit is required to
provide sufficient local oscillator signal for the frequency
multiplier.
Frequency multiplier
The frequency multiplier is an emitter-coupled pair driving
an external balanced tuned circuit. Its bias current is set by
external resistor R4 to typically 190 A (173 MHz), 350 A
(470 MHz) and 1 mA (930 MHz). The oscillator signal is
internally AC coupled to one input of the emitter-coupled
pair while the other input is internally grounded via a
capacitor. The frequency multiplier output signal between
pins VO1MUL and VO2MUL drives the upper switching
stages of the mixers. The bias voltage on pins VO1MUL
and VO2MUL is set by external resistor R3 to allow
sufficient voltage swing at the mixer outputs. The value of
R3 depends on the operating frequency: 1.5 k
(173 MHz), 820
Low noise amplifiers, active filters and gyrator filters
The low noise amplifiers ensure that the noise of the
following stages does not affect the overall noise figure.
The following active filters before the gyrator filters reduce
the levels of large signals from adjacent channels. Internal
AC couplings block DC offsets from the gyrator filter
inputs.
The gyrator filters implement the transfer function of a 7th
order elliptic filter. Their cut-off frequencies are determined
by the 47 k external resistor R2 between pins RGYR and
COM. The gyrator filter output signals are available on IF
test pins TPI and TPQ.
Limiters
The gyrator filter output signals are amplified in the limiter
amplifiers to obtain IF signals with removed amplitude
information.
Demodulator
The limiter amplifier output signals are fed to the
demodulator. The demodulator output DO is going LOW or
HIGH depending upon which of the input signals has a
phase lead.
(470 MHz) and 330
Product specification
UAA2080
(930 MHz).