XCF16PVO48C XILINX [Xilinx, Inc], XCF16PVO48C Datasheet - Page 44
![no-image](/images/no-image-200.jpg)
XCF16PVO48C
Manufacturer Part Number
XCF16PVO48C
Description
Platform Flash In-System Programmable Configuration PROMs
Manufacturer
XILINX [Xilinx, Inc]
Datasheet
1.XCF16PVO48C.pdf
(46 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XCF16PVO48C
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
Revision History
The following table shows the revision history for this document.
DS123 (v2.11.1) March 30, 2007
Product Specification
04/29/03
06/03/03
11/05/03
11/18/03
12/15/03
05/07/04
Date
R
Version
1.0
1.1
2.0
2.1
2.2
2.3
Xilinx Initial Release.
Made edits to all pages.
Major revision.
Pinout corrections as follows:
•
•
•
• Added specification (4.7kΩ) for recommended pull-up resistor on OE/RESET pin to section
• Added paragraph to section
• Section
• Section
•
• Section
• Section
•
• Section
•
• Section
• Section
• Section
• (Continued on next page)
• Section
• Section
• Section
•
Table
♦ For VO48 package, removed 38 from VCCINT and added it to VCCO.
♦ For FS48 package, removed pin D6 from VCCINT and added it to VCCO.
Table 15
♦ For pin D6, changed name from VCCINT to VCCO.
♦ For pin A4, changed name from GND to DNC.
Figure 16
"Reset and Power-On Reset Activation," page
and/or buffer on the DONE pin.
itemized features.
descriptive text.
Table 2, page
following, five instances: Added instruction to tie CF High if it is not tied to the FPGA’s PROG_B
(PROGRAM) input.
Figure 6, page
CF pin in each configuration.
Table 12, page
the Low state of CF.
♦ Revised footnote callout number on T
♦ Added Footnote (2) callout to T
♦ Added Typical (Typ) parameter columns and parameters for V
♦ Added 1.5V operation parameter row to V
♦ Revised V
♦ Added parameter row T
♦ Added parameter row and parameters for parallel configuration mode, ’P’ devices, to I
♦ Added Footnote (1) and Footnote (2) with callouts in the Test Conditions column for I
♦ Corrected description for second T
♦ Revised Footnote (7) to indicate V
♦ Applied Footnote (7) to second T
Footnote (5)T
Table 14, page
♦ Added additional state conditions to CLK description.
♦ Added function of resetting the internal address counter to CF description.
I
CCINTS
14:
"Features," page
"Description," page 1
"Design Revisioning," page
"PROM to FPGA Configuration Mode and Connections Summary," page 12
"I/O Input Voltage Tolerance and Power Sequencing," page
"Absolute Maximum Ratings," page
"Supply Voltage Requirements for Power-On Reset and Power-Down," page
"Recommended Operating Conditions," page
"DC Characteristics Over Operating Conditions," page
"AC Characteristics Over Operating Conditions," page
"AC Characteristics Over Operating Conditions When Cascading," page
(FS48 package):
(VO48 package): For pin 38, changed name from VCCINT to VCCO.
, I
CCOS
IH
CYC
3: Updated Virtex-II configuration bitstream sizes.
16, through
25: Added CF column to truth table, and added an additional row to document
39:
Min, 2.5V operation, from 2.0V to 1.7V.
, and I
Min and T
www.xilinx.com
Platform Flash In-System Programmable Configuration PROMs
CCJS
1: Added package styles and 33 MHz configuration speed limit to
IN
Figure 13, page
CAC
"Standby Mode," page
, to define active and standby mode requirements.
and Max parameters
and following: Added state conditions for CF and BUSY to the
Min formulas.
VCC
CYC
10: Rewritten.
CCO
CAC
.
OER
parameter line.
Revision
= 3.3V.
parameter line to show parameters for 1.8V V
23: Added footnote indicating the directionality of the
26: Revised V
IL
from Footnote (4) to Footnote (3).
24.
and V
25, concerning use of a pull-up resistor
IH
27:
, ’P’ devices.
IN
and V
29:
28:
CCINT
TS
24: Rewritten.
for ’P’ devices.
and V
CCO
/V
36: Revised
CCJ
and
26:
.
CCJ
CCO
CCO
,
.
.
44