PCF88332DA PHILIPS [NXP Semiconductors], PCF88332DA Datasheet - Page 20
PCF88332DA
Manufacturer Part Number
PCF88332DA
Description
STN RGB - 132 X 132 X 3 driver
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.PCF88332DA.pdf
(112 pages)
- Current page: 20 of 112
- Download datasheet (464Kb)
Philips Semiconductors
6.2.8
By sending the Sleep_IN command, the PCF8833
immediately enters the Power-down mode, also referred to
as the Sleep mode. In the Sleep mode the output voltages
of all LCD driver pins (rows and columns) are at V
(ground, all pixels are in off state), and the LCD supply
generation circuit and the oscillator are switched off. The
Sleep_IN command does not change the state of the
DISPON/DISPOFF and BSTRON/BSTROFF commands,
but has the same effect as DISPOFF and BSTROFF;
see Table 17.
Table 16 Sleep_IN register bits
Table 17 Sleep_IN/OUT and BSTR_ON/OFF combination
Note
1. Booster is the built-in DC-to-DC converter also called voltage multiplier or charge pump.
6.2.9
This command must be sent to allow the PCF8833 to
power-up (see Fig.4).
DISPON and BSTRON are set with a reset, the PCF8833
will start-up with Sleep_OUT following the built-in start-up
sequence which generates the requested voltages and
switches on the display, unless DISPOFF and/or
BSTROFF was sent after the last reset.
For the effects of possible combinations of commands
Sleep_IN/Sleep_OUT and BSTRON/BSTROFF; see
Table 17.
Figure 4 illustrates the flow when sending the Sleep_OUT
command. The display is only switched on, when the
internally generated voltage V
2003 Feb 14
STN RGB - 132
D/C
0
BSTER_ON/BSTER_OFF
S
S
LEEP
LEEP
_IN
_OUT
7
0
OFF
OFF
ON
ON
6
0
LCD2
132
is high enough.
3 driver
5
0
Sleep_IN/Sleep_OUT
SS1
4
1
OFF
OFF
ON
ON
20
While in Sleep_IN mode all commands and data can be
sent and will be executed as in the Sleep_OUT state,
except some OTP related commands and temperature
readout related commands. In the Sleep_IN mode no
effect on the display can be seen.
The Sleep_IN mode is exited by command Sleep_OUT;
see Section 6.2.9.
This time is self adapting and therefore dependent on
application conditions:
It is longer for:
– Low V
– Higher resistors in supply wires and/or external
– Higher external capacitors
– Higher required V
Some other conditions, which may affect start-up time
are:
– Partial/full mode
– Selected bias system
– Temperature
– Selected temperature coefficients.
3
0
capacitors
DD2
2
0
LCD2
1
0
voltage.
Booster
Objective specification
OFF
OFF
OFF
ON
0
0
PCF8833
(1)
DEFAULT
10H
Related parts for PCF88332DA
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors