LTC2226 LINER [Linear Technology], LTC2226 Datasheet - Page 12

• Manufacturer Part Number: LTC2226
• Description: 12-Bit, 65/40/25Msps Low Power 3V ADCs
• Manufacturer: LINER [Linear Technology]

PIN FUNCTIONS
LTC2228/LTC2227/LTC2226
A
A
REFH (Pins 3, 4): ADC High Reference. Short together and
bypass to Pins 5, 6 with a 0.1μF ceramic chip capacitor as
close to the pin as possible. Also bypass to Pins 5, 6 with
an additional 2.2μF ceramic chip capacitor and to ground
with a 1μF ceramic chip capacitor.
REFL (Pins 5, 6): ADC Low Reference. Short together and
bypass to Pins 3, 4 with a 0.1μF ceramic chip capacitor as
close to the pin as possible. Also bypass to Pins 3, 4 with
an additional 2.2μF ceramic chip capacitor and to ground
with a 1μF ceramic chip capacitor.
V
ceramic chip capacitors.
GND (Pin 8): ADC Power Ground.
CLK (Pin 9): Clock Input. The input sample starts on the
positive edge.
SHDN (Pin 10): Shutdown Mode Selection Pin. Connecting
SHDN to GND and OE to GND results in normal operation
with the outputs enabled. Connecting SHDN to GND and
OE to V
high impedance. Connecting SHDN to V
results in nap mode with the outputs at high impedance.
Connecting SHDN to V
mode with the outputs at high impedance.
OE (Pin 11): Output Enable Pin. Refer to SHDN pin
function.
12
IN
IN
DD
+
–
(Pins 7, 32): 3V Supply. Bypass to GND with 0.1μF
(Pin 1): Positive Differential Analog Input.
(Pin 2): Negative Differential Analog Input.
DD
results in normal operation with the outputs at
DD
and OE to V
DD
DD
results in sleep
and OE to GND
NC (Pins 12, 13): Do Not Connect These Pins.
D0-D11 (Pins 14, 15, 16, 17, 18, 19, 22, 23, 24, 25, 26,
27): Digital Outputs. D11 is the MSB.
OGND (Pin 20): Output Driver Ground.
OV
Bypass to ground with 0.1μF ceramic chip capacitor.
OF (Pin 28): Over/Under Flow Output. High when an over
or under fl ow has occurred.
MODE (Pin 29): Output Format and Clock Duty Cycle
Stabilizer Selection Pin. Connecting MODE to GND selects
offset binary output format and turns the clock duty cycle
stabilizer off. 1/3 V
and turns the clock duty cycle stabilizer on. 2/3 V
2’s complement output format and turns the clock duty
cycle stabilizer on. V
format and turns the clock duty cycle stabilizer off.
SENSE (Pin 30): Reference Programming Pin. Connecting
SENSE to V
input range. V
input range. An external reference greater than 0.5V and
less than 1V applied to SENSE selects an input range of
±V
V
Bypass to ground with 2.2μF ceramic chip capacitor.
Exposed Pad (Pin 33): ADC Power Ground. The Exposed
Pad on the bottom of the package needs to be soldered
to ground.
CM
SENSE
DD
(Pin 31): 1.5V Output and Input Common Mode Bias.
(Pin 21): Positive Supply for the Output Drivers.
. ±1V is the largest valid input range.
CM
DD
selects the internal reference and a ±0.5V
selects the internal reference and a ±1V
DD
DD
selects offset binary output format
selects 2’s complement output
DD
selects
222876fb