kac-9637 ETC-unknow, kac-9637 Datasheet - Page 8

• Manufacturer Part Number: kac-9637
• Description: Cmos Image Sensor 648 H X 488 V Vga 68 Fps Monochrome Cis
• Manufacturer: ETC-unknow

IMAGE SENSOR SOLUTIONS
Video Amplifier Specifications
The following specifications apply for all VDD pins= +3.0V. Boldface limits apply for TA = T
AC Electrical Characteristics
The following specifications apply for All VDD pins = +3.0V. Boldface limits apply for T
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
www.kodak.com/go/imagers 585-722-4385
Symbol
Symbol
T
T
F
F
rc
T
reset
mclk
T
hclk
, T
ch
cl
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate con-
ditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications
and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions
listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to vss_dig = vss_ana = vss_adc = vss_od1 = vss_od2 = 0V, unless otherwise
specified.
When the voltage at any pin exceeds the power supplies (VIN < [vss_dig or vss_ana or vss_adc or vss_od1 or vss_od2]
or VIN > [vdd_dig or vdd_ana or vdd_adc or vdd_od1 or vdd_od2]), the current at that pin should be limited to 25mA.
The 50mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with
an input current of 25mA to two.
The absolute maximum junction temperature (TJmax) for this device is 150
is dictated by TJmax, the junction-to-ambient thermal resistance (Θ
culated using the formula PDMAX = (TJmax - TA)/Θ
and 1,449 mW at the maximum operating ambient temperature of 50
under normal operation will typically be about 215 mW. The values for maximum power dissipation listed above will be
reached only when the KAC-9637 is operated in a severe fault condition.
Human body model is 100pF capacitor discharged through a 1.5kΩ resistor. Machine model is 220pF discharged through
ZERO Ohms.
See AN450, “Surface Mounting Methods and Their Effect on Product Reliability”, or the section entitled “Surface Mount”
found in any post 1986 National Semiconductor Linear Data Book, for other methods of soldering surface mount devices.
The analog inputs are protected as shown below. Input voltage magnitude up to 500mV beyond the supply rails will not
damage this device. However, input errors will be generated If the input goes above AV+ and below AGND.
Typical figures are at TJ = 25
Test limits are guaranteed to AOQL (Average Outgoing Quality Level).
fc
Input Clock Frequency
Clock High Time
Clock Low Time
Clock Duty Cycle
Clock Input Rise and Fall Time
Internal System Clock Fre-
quency
Reset pulse width
Gain Resolution
Maximum Gain
Minimum Gain
Parameter
Step Size
Parameter
o
C, and represent most likely parametric norms
@ CLK
@ CLK
@ CLK
Conditions
(Gain / Resolution)
max
max
max
JA
Conditions
8
. In the 48-pin LCC, Θ
JA
note 9
45/55
16.0
16.0
Min
), and the ambient temperature (TA), and can be cal-
1.0
12
12
o
C. Note that the power dissipation of this device
o
JA
C. The maximum allowable power dissipation
A
is 69
(note 9)
= T
Typical
note 8
Min
50/50
MIN
MIN
3
o
C/W, so PDMAX = 1,811mW at 25
to T
to T
MAX
(note 8)
Typical
MAX
0.125
0.0
16
7
: all other limits T
note 9
: all other limits T
Email:[e-mail]
55/45
Max
27
27
(note 9)
Max
min/max
Units
MHz
MHz
ns
ns
µs
ns
A
A
= 25
Units
= 25
Bits
dB
dB
dB
o
o
C
C.
o
C