am49pdl129bh85it Meet Spansion Inc., am49pdl129bh85it Datasheet - Page 60

• Manufacturer Part Number: am49pdl129bh85it
• Description: Stacked Multi-chip Package Mcp Flash Memory And Psram, 128 Megabit 8m ? 16-bit Cmos 3.0 Volt-only, Simultaneous Operation Flash Memory And 32 Mbit 2m ? 16-bit Cmos Pseudo Static Ram With Page Mode
• Manufacturer: Meet Spansion Inc.

ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –55°C to +125°C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . . –40°C to +85°C
Voltage with Respect to Ground
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V.
2. Minimum DC input voltage on pins RESET#, and
3. No more than one output may be shorted to ground at a
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (T
V
V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
ESD IMMUNITY
Spansion Flash memory Multi-Chip Products (MCPs)
may contain component devices that are developed by
FASL LLC (“Spansion components”) and component
58
CC
CC
V
RESET# (Note 2) . . . . . . . . . . . .–0.5 V to +12.5 V
WP#/ACC . . . . . . . . . . . . . . . . . . –0.5 V to +10.5 V
All other pins (Note 1) . . . . . . –0.5 V to V
During voltage transitions, input or I/O pins may
overshoot V
Maximum DC voltage on input or I/O pins is V
See Figure 8. During voltage transitions, input or I/O pins
may overshoot to V
Figure 9.
WP# /ACC is –0 .5 V. D ur ing volt age trans itions,
WP#/ACC, and RESET# may overshoot V
periods of up to 20 ns. See Figure 8. Maximum DC input
voltage on pin RESET# is +12.5 V which may overshoot
to +14.0 V for periods up to 20 ns. Maximum DC input
voltage on WP#/ACC is +9.5 V which may overshoot to
+12.0 V for periods up to 20 ns.
time. Duration of the short circuit should not be greater
than one second.
f/V
f/V
CC
CC
CC
f, V
s for standard voltage range . . 2.7 V to 3.3 V
s Supply Voltages
CC
s (Note 1) . . . . . . . . . . . . –0.5 V to +4.0 V
SS
to –2.0 V for periods of up to 20 ns.
CC
+2.0 V for periods up to 20 ns. See
A
) . . . . . . . . . –40°C to +85°C
A D V A N C E
Am49PDL127BH/Am49PDL129BH
SS
to –2.0 V for
CC
CC
+0.5 V
+0.5 V.
I N F O R M A T I O N
devices that are developed by a third party (‘third-party
components”).
Spansion components are tested and guaranteed to
the ESD immunity levels listed in the corresponding
Spansion Flash memory Qualification Database.
Third-party components are neither tested nor guaran-
teed by FASL LLC for ESD immunity. However, ESD
test results for third-party components may be avail-
able from the component manufacturer. Component
manufacturer contact information is listed in the Span-
sion MCP Qualification Report, when available.
The Spansion Flash memory Qualification Database
and Spansion MCP Qualification Report are available
from AMD and Fujitsu sales offices.
+0.8 V
–0.5 V
–2.0 V
+2.0 V
+0.5 V
2.0 V
V
V
CC
CC
Figure 10. Maximum Positive
Figure 9. Maximum Negative
Overshoot Waveform
Overshoot Waveform
20 ns
20 ns
20 ns
20 ns
December 16, 2003
20 ns
20 ns