71m6515h Maxim Integrated Products, Inc., 71m6515h Datasheet - Page 53
![no-image](/images/no-image-200.jpg)
71m6515h
Manufacturer Part Number
71m6515h
Description
71m6515h Energy Meter Ic
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.71M6515H.pdf
(57 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIAN
Quantity:
317
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIA
Quantity:
20 000
Company:
Part Number:
71m6515h-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
80
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
20 000
Company:
Part Number:
71m6515h-IGTW/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Communication Steps for Interrupt Method:
The following is a list of commands required from the host processor to establish communication with the 71M6515H.
Page: 53 of 57
1)
2)
3)
4)
5)
6)
7)
8)
9)
10) Wait for the IRQZ pin to go low.
11) After receiving the interrupt, read at least one accumulated value register (WATTH_X, or VAH_X, or VARH_X) in order
12) After reading the required data from the 71M6515H, configuration changes should be made, if necessary. These con-
Establish host baud rate and data format as required by the 71M6515H.
Configure the DIO pins (D0…D7), if required, using the D_CONFIG register
Configure the 71M6515H by selecting the CE image (bits 23-22), equation (bits 7-5), pulse rate (bits 26-25), followed
by enabling the CE (bit 4 in the CONFIG register). The bit pattern sent to CONFIG should have all bits set to their
default state, as given in the Register Table.
Write the TEMP_RAW value obtained at calibration into the TEM_NOM register to enable temperature compensation.
Write the calibration coefficients into registers CAL_IA, CAL_VA, CAL_IB, CAL_VB, CAL_C, CAL_VC, PHADJ_A,
PHADJ_B, PHADJ_C. Write calibration values to the VFEED_A/B/C registers if the Rogowski image is used.
Configure WRATE with the value required to generate the desired pulse rate.
Establish creep, sag and over/under voltage/current thresholds, if necessary, by writing values to the
CREEP_THRSLD, SAG, VI_PTHRESH, and VI_THRSHLD registers.
Set the READY bit in the status mask STMASK in order to enable the generation of interrupts on the IRQZ pin.
Read at least one accumulated value register (WATTH_X, or VAH_X, or VARH_X).
to maintain interrupt generation. Read the bits in the STATUS word to detect potential faults (overflow signaled by the
XOVF flag or uninitialized condition signaled by the BOOTUP flag) or warnings and events (sag, creep, excessive
voltage or current, DIO signal changes). If necessary, take corrective action.
figuration changes should be completed before the pre-processing period begins again.
1000ms
post-processor
© 2005-2008 TERIDIAN Semiconductor Corporation
commands
6515H not
from host
Figure 21: Timing Diagram (Host Polling)
330ms
ready
active
read
6515H data
2000ms
commands
6515H not
from host
ready
read
post-processor
active
330ms
Energy Meter IC
6515H data
DATA SHEET
71M6515H
time
MARCH 2008
V1.4