71m6515h Maxim Integrated Products, Inc., 71m6515h Datasheet - Page 38
![no-image](/images/no-image-200.jpg)
71m6515h
Manufacturer Part Number
71m6515h
Description
71m6515h Energy Meter Ic
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.71M6515H.pdf
(57 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIAN
Quantity:
317
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIA
Quantity:
20 000
Company:
Part Number:
71m6515h-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
80
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
20 000
Company:
Part Number:
71m6515h-IGTW/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
STMASK (0x15)
Page: 38 of 57
Bit 7: This bit (1SECI, toggles every second. It is controlled by the RTC.
Bit 8: This bit (VXEDGE), when set, indicates a change in state of VX comparator. This bit is updated every accumulation
interval.
Bit 9: This bit (DEDGE), when set, indicates a change in state of any selected DIO pin. This bit is updated every
accumulation interval. Pins have to be configured to generate the DEDGE flag using the DIO_INT_CTRL bits in the
D_CONFIG register.
Bit 10: This bit (XOVF), when set, indicates that the host failed to read at least one of the Wh values. Between interrupts
(indicated by the READY bit in the STATUS word), the 71M6515H expects the host to read at least one of the WATTHR_A,
WATTHR_B, or WATTHR_C values.
Bit 11: This bit (READY), when set, indicates that the 71M6515H has fresh output values ready for the host. Setting this bit
in STMASK will enable the hardware interrupt output pin IRQZ.
Bit 14-12: These bits (bit 12 for phase A, bit 13 for phase B, bit 14 for phase C), when set, indicate that the energy received
from element A, B, or C is below the creep threshold defined in the CREEP_THRSHLD register or that the current in
elements A, B, or C is below the threshold defined in bits 15-0 of the START_THRESHLD register. The creep condition
flagged by bits 14-12 of the STATUS register indicates that Wh, VARh, and IRMS measurements of element A, B, or C have
been zeroed out. Consequently, accumulation did not occur.
Bit 15: This bit (CMD_IGNORED), when set, indicates that the 71M6515H ignored the last command received from the
host. The reason can be any type of command incompatibility, e.g. attempts to write to a read-only register.
Bit 16: This bit (PULSEW_ERR), when set, indicates that the pulse generator PULSEW is configured for external (host)
input, but did not receive an update during the previous accumulation interval.
Bit 17: This bit (PULSER_ERR), when set, indicates that the pulse generator PULSER is configured for external (host) input,
but did not receive an update during the previous accumulation interval.
Bit 18: This bit (PULSE3_ERR), when set, indicates that the pulse generator PULSE3 is configured for external (host) input,
but did not receive an update during the previous accumulation interval.
Bit 19: This bit (PULSE4_ERR), when set, indicates that the pulse generator PULSE4 is configured for external (host) input,
but did not receive an update during the previous accumulation interval.
The four bytes in this register enable interrupts when the corresponding bit in the STATUS register is set. The default value
for STMASK is zero.
When a bit in the STMASK register is set, an interrupt (IRQZ) is generated as soon as the corresponding bit in the STATUS
register is set. Interrupts indicated by IRQZ do not necessarily have to be synchronized with accumulation intervals. For
example, the toggling of a signal applied to the DIO pins (D0…D7), when the interrupt is enabled with the DIO_INT_CTRL
register, can cause an interrupt at any time.
© 2005-2008 TERIDIAN Semiconductor Corporation
Energy Meter IC
DATA SHEET
71M6515H
MARCH 2008
V1.4