71m6515h Maxim Integrated Products, Inc., 71m6515h Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
71m6515h
Manufacturer Part Number
71m6515h
Description
71m6515h Energy Meter Ic
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.71M6515H.pdf
(57 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIAN
Quantity:
317
Part Number:
71m6515h-IGT
Manufacturer:
TERIDIA
Quantity:
20 000
Company:
Part Number:
71m6515h-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
80
Part Number:
71m6515h-IGTW
Manufacturer:
TERIDIAN
Quantity:
20 000
Company:
Part Number:
71m6515h-IGTW/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Oscillator
The oscillator drives a standard 32.768kHz watch crystal. Crystals of this type are accurate and do not require a high current
oscillator circuit. The 71M6515H oscillator has been designed specifically to handle watch crystals and is compatible with their
high impedance and limited power handling capability. The oscillator power dissipation is very low to maximize the lifetime of
any battery backup device attached to VBAT. Using PLL techniques, all internal clocks, such as the 4.915MHz clock for the
ADC and the post-processor, are derived from the watch crystal frequency.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. In the absence of V3P3, it is powered by the battery-backed up supply. The
RTC consists of a counter chain and output registers. The counter chain consists of registers for seconds, minutes, hours, day
of week, day of month, month, and year. The nominal quadratic temperature coefficient of the crystal is automatically
compensated in the RTC. The RTC is capable of processing leap years.
I/O Peripherals
The 71M6515H includes several I/O peripheral functions that improve the functionality of the device and reduce the component
count for most meter applications. The I/O peripherals include a UART and digital I/O.
Digital I/O
The device includes eight pins of general purpose digital I/O (D0…D7). Each pin can be configured independently as an input
or output with the D_DIR bits. Inputs are standard CMOS with no pull-ups or pull-downs. Outputs are standard CMOS. The
DIO pins are controlled by the D_CONFIG register.
Immediately after reset or power-up, D0 through D7 are in tri-state mode (floating). 140 ms after reset, D0 through D7
are configured as outputs and driven low.
UART Host Interface
The UART is a dedicated 2-wire serial interface, which can communicate with the host processor. The operation of each pin is
as follows:
The 71M6515H has several on-chip registers, which can be read and written. All transfers start with a stream of 8-bit bytes
(LSB first) from the host on the RX input, followed by a (possibly null) stream of 8-bit bytes (LSB first) to the host on the TX
output (see Figure 10 and Figure 11). The UART is configured as 8N1 (8 bits, no parity, 1 stop bit).
If the READY bit in STMASK is enabled, the IRQZ pin can be used to signal data availability to the host. If data read cycles
exceeding 1 second are used, care should be taken to prevent data overflow.
UART Write Register Operation
The registers are written by sending a byte, consisting of a starting register address in the seven MSBs and ‘0’ in the LSB
indicating this is a write operation. It is followed by a one byte length of bytes to write. If more bytes arrive than fit in the
addressed register, subsequent registers will be written. The bytes are processed in “big-endian” order (i.e. most significant
byte first). See Figure 10 (read bits and bytes from left to right).
Page: 18 of 57
RX: Is the pin accepting the serial input data. It inputs data to internal registers. The bytes are input LSB first. The voltage
applied to this pin must be restricted to 0 to 3.6V.
TX: Is the pin used for serial output data. It outputs the contents of a block of internal registers. The bytes are output LSB
first.
BAUD_RATE: The baud rate can be selected with the BAUD_RATE pin (38.4bps when high, 19.2bps when low).
UARTCSZ: This pin enables the UART when low. The UART can be reset by taking UARTCSZ briefly to the high state and
then low again.
© 2005-2008 TERIDIAN Semiconductor Corporation
Internal Resources
Energy Meter IC
DATA SHEET
71M6515H
MARCH 2008
V1.4