dp83932c-20 National Semiconductor Corporation, dp83932c-20 Datasheet - Page 28
dp83932c-20
Manufacturer Part Number
dp83932c-20
Description
Mhz Sonictm Systems-oriented Network Interface Controller
Manufacturer
National Semiconductor Corporation
Datasheet
1.DP83932C-20.pdf
(98 pages)
- Current page: 28 of 98
- Download datasheet (2Mb)
4 0 SONIC Registers
4 3 REGISTER DESCRIPTION (Continued)
4 3 1 Command Register (Continued)
Bit
3
2
1
0
RXEN RECEIVER ENABLE
Setting this bit enables the receive buffer management engine to begin buffering data to memory Setting this bit
resets the RXDIS bit Note If this bit is set while the MAC unit is currently receiving a packet both RXEN and RXDIS
are set until the network goes inactive (i e the SONIC will not start buffering in the middle of a packet being
received)
RXDIS RECEIVER DISABLE
Setting this bit disables the receiver from buffering data to memory or the Receive FIFO If this bit is set during the
reception of a packet the receiver is disabled only after the packet is processed The RXEN bit is reset when the
receiver is disabled Tally counters remain active regardless of the state of this bit
Note If this bit is set while the SONIC is currently receiving a packet both RXEN and RXDIS are set until the packet is fully received When both
RXEN and RXDIS are set RXDIS could be cleared by writing zero to it
TXP TRANSMIT PACKET(S)
Setting this bit causes the SONIC to transmit packets which have been set up in the Transmit Descriptor Area (TDA)
The SONIC loads its appropriate registers from the TDA then begins transmission The SONIC clears this bit after
any of the following conditions have occurred (1) transmission had completed (i e after the SONIC has detected
EOL
occurred This condition occurs when any of the following bits in the TCR have been set EXC EXD FU or BCM
This bit must not be set if a Load CAM operation is in progress (LCAM is set) The SONIC will lock up if both bits are
set simultaneously
HTX HALT TRANSMISSION
Setting this bit halts the transmit command after the current transmission has completed TXP is reset after
transmission has halted The Current Transmit Descriptor Address (CTDA) register points to the last descriptor
transmitted The SONIC samples this bit after writing to the TXpkt status field
e
1) (2) the Halt Transmission command (HTX) has taken effect or (3) a transmit abort condition has
(Continued)
28
Description
Related parts for dp83932c-20
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: