cs4239 Cirrus Logic, Inc., cs4239 Datasheet - Page 25

• Manufacturer Part Number: cs4239
• Description: Crystalclear? Ortable Isa Audio System Logic
• Manufacturer: Cirrus Logic, Inc.

EECS
CAL7-CAL0
Bytes 19 through 21 map the interrupt number to
the actual interrupt pins A - F. As shown in Ta-
ble 2, the byte 20 default is 0xB9; therefore,
IRQ C, which is the lower nibble, maps to the
ISA interrupt 9. Likewise IRQ D, which is the
upper nibble, maps to the ISA interrupt 11
(0Bh).
Byte 22 maps the DMA channel number to the
actual DMA pins A and B. As shown in the ta-
ble, the byte 22 default is 0x10; therefore,
DRQA/DACKA is the lower nibble which maps
to the ISA DMA channel 0. Likewise
DRQB/DACKB is the upper nibble which maps
to the ISA DMA channel 1.
Byte 23 maps DMA C and IRQ G. The lower
nibble maps DMA C and defaults to DMA 3.
The upper nibble supports the seventh IRQ,
IRQ G. The default is disabled (0), providing
backwards compatibility with other Cirrus ISA
DS253PP2
HW Config. Byte 17: CDbase Address Length,
Default = 00000100
CAL7
D7
CAL6
D6
CAL5
D5
ity when AUX1 analog inputs are
substituted for LINE analog inputs
which are no longer available.
EEPROM Checksum. If set, indicates
that Hardware Configuration Byte 15
is a checksum for the entire
EEPROM (starting after 55h/BBh).
CDbase Address Length. Determines
the address length decode for the
primary CDROM address, CDbase.
00000001 - CDCS low for 1 byte
00000010 - CDCS low for 2 bytes
00000100 - CDCS low for 4 bytes
00001000 - CDCS low for 8 bytes
00010000 - CDCS low for 16 bytes
00100000 - CDCS low for 32 bytes
01000000 - CDCS low for 64 bytes
10000000 - CDCS low for 128 bytes
xxx - all others, RESERVED
CAL4
D4
CAL3
D3
CAL2
D2
CAL1
D1
CAL0
D0
audio parts. If IRQ G is connected to an ISA in-
terrupt (typically 10), then this byte must be
modified to reflect the hardware connection.
Hostload Procedure
This procedure is provided for backwards com-
patibility with the CS4236. Since the E
allows all resource and firmware patch data to be
loaded at power-up, this procedure is typically
only used with motherboard devices that do not
include an E
data from the host to the part’s internal RAM,
use the following sequence:
1. Configure Control I/O base address,
2. Write 57h (Jump to ROM) command to
3. Download the PnP Resource data.
CTRLbase, by one of two methods: regular
PnP cycle or Crystal Key method.
CTRLbase+5.
a. The host can use the regular PnP cycle to
b. If the Crystal Key method is used:
a. Send download command by writing AAh
b. Send starting download address (4000h)
program the CTRLbase, and then place the
chip in the wait_for_key_state
to CTRLbase+5.
by writing low byte (00h) first, and then
high byte (40h) to CTRLbase+5.
First, send the 32-byte Crystal key to I/O
address port (AP).
Second, configure logical device 2 base
address, CTRLbase, by writing to AP
(15h, 02h, 47h, xxh, xxh, 33h, 01h, 79h).
Note: The two xxh represent the base_ad-
dress_high and base_address_low
respectively. The default is: 01h, 20h.
CrystalClear Portable ISA Audio System
2
PROM. To download PnP resource
TM
CS4239
2
PROM
25