si3210 ETC-unknow, si3210 Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
si3210
Manufacturer Part Number
si3210
Description
Proslic Programmable Cmos Slic/codec With Ringing/battery Voltage Generation
Manufacturer
ETC-unknow
Datasheet
1.SI3210.pdf
(122 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
si3210-E-FMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
si3210-FM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
si3210-FTR
Manufacturer:
SILCONX
Quantity:
160
Part Number:
si3210-FTR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
si3210-GT
Manufacturer:
MICROCHIP
Quantity:
3 200
Part Number:
si3210-GT
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
si3210-KS
Manufacturer:
PHILIPPNS
Quantity:
20 000
Company:
Part Number:
si3210-KT
Manufacturer:
SiliconLa
Quantity:
2 383
Company:
Part Number:
si3210-KTR
Manufacturer:
WINBOND
Quantity:
43
Si 3210/ Si3 211/S i32 12
DC-DC Converter Enhancements
Silicon
enhancements to the dc-dc converter. The first is a
multi-threshold error control algorithm that enables the
dc-dc converter to adjust more quickly to voltage
changes. This option is enabled by setting DCSU = 1
(direct Register 108, bit 5). The second enhancement is
an audio band filter that removes audio band noise from
the dc-dc converter control loop. This option is enabled
by setting DCFIL = 1 (direct Register 108, bit 1).
DC-DC Converter During Ringing
When the ProSLIC enters the ringing state, it requires
voltages well above those used in the active mode. The
voltage to be generated and regulated by the dc-dc
converter during a ringing burst is set using the VBATH
register (direct Register 74). VBATH can be set between
0 and –94.5 V in 1.5 V steps. To avoid clipping the
ringing signal, V
amplitude. At the end of each ringing burst the dc-dc
converter adjusts back to active state regulation as
described above.
External Battery Switching (Si3211 and Si3212 Only)
The Si3211 and Si3212 support switching between two
battery voltages. The circuit for external battery
switching is defined in Figure 12. Typically a high
voltage battery (e.g., –70 V) is used for on-hook and
ringing states, and a low voltage battery (e.g., –24 V) is
used for the off-hook condition. The ProSLIC uses an
external transistor to switch between the two supplies.
When the ProSLIC changes operating states, it
automatically switches battery supplies if the automatic/
manual control bit ABAT (direct Register 67, bit 3) is set.
For example, the ProSLIC will switch from high battery
to low battery when it detects an off-hook event through
either a ring trip or loop closure event. If automatic
battery selection is disabled (ABAT = 0), the battery is
selected by the Battery Feed Select bit, BATSL (direct
Register 66, bit 1).
Silicon revisions C and higher support the option to add
a 60 ms debounce period to the battery switching circuit
when transitioning from high battery to low battery. This
option is enabled by setting SWDB = 1
Register 108, bit 3). This debounce minimizes battery
transitions in the case of pulse dialing or other quick on-
hook to off-hook transitions.
30
revisions
BATH
C
must be set larger than the ringing
and
higher
support
Preliminary Rev. 1.11
(direct
two
Tone Generation
Two digital tone generators are provided in the ProSLIC.
They allow the generation of a wide variety of single or
dual tone frequency and amplitude combinations and
spare the user the effort of generating the required
POTS signaling tones on the PCM highway. DTMF, FSK
(caller ID), call progress, and other tones can all be
generated on-chip. The tones can be sent to either the
receive or transmit paths (see Figure 23 on page 40).
Tone Generator Architecture
A simplified diagram of the tone generator architecture
is shown in Figure 18. The oscillator, active/inactive
timers, interrupt block, and signal routing block are
connected to give the user flexibility in creating audio
signals. Control and status register bits are placed in the
figure to indicate their association with the tone
generator architecture. These registers are described in
more detail in Table 27.