S29GL256N10TFI023 ETC, S29GL256N10TFI023 Datasheet - Page 64
S29GL256N10TFI023
Manufacturer Part Number
S29GL256N10TFI023
Description
MirrorBit Flash Family
Manufacturer
ETC
Datasheet
1.S29GL256N10TFI023.pdf
(110 pages)
- Current page: 64 of 110
- Download datasheet (3Mb)
64
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming
operation or a Write to Buffer programming operation so that data can be read
from any non-suspended sector. When the Program Suspend command is written
during a programming process, the device halts the program operation within 15
µs maximum (5µs typical) and updates the status bits. Addresses are not re-
quired when writing the Program Suspend command.
After the programming operation has been suspended, the system can read array
data from any non-suspended sector. The Program Suspend command may also
be issued during a programming operation while an erase is suspended. In this
case, data may be read from any addresses not in Erase Suspend or Program
Suspend. If a read is needed from the SecSi Sector area (One-time Program
area), then user must use the proper command sequences to enter and exit this
region. Note that the SecSi Sector autoselect, and CFI functions are unavailable
when program operation is in progress.
The system may also write the autoselect command sequence when the device
is in the Program Suspend mode. The system can read as many autoselect codes
as required. When the device exits the autoselect mode, the device reverts to the
Program Suspend mode, and is ready for another valid operation. See Autoselect
Command Sequence for more information.
Note:
mand sequence.
Increment Address
See Table
S29GLxxxN MirrorBitTM Flash Family
Figure 2. Program Operation
A d v a n c e
Embedded
in progress
algorithm
12
Program
and Table
No
Command Sequence
13
I n f o r m a t i o n
Write Program
Last Address?
Programming
from System
Verify Data?
for program com-
Completed
Data Poll
START
Yes
Yes
No
27631A4 May 13, 2004
Related parts for S29GL256N10TFI023
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KLPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KQPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
BC41B143A05-IRK-E4BlueCpre 4-ROM Single Chip Bluetooth v2.0 System with EDR
Manufacturer:
ETC ETC
Datasheet: