S29GL256N10TFI023 ETC, S29GL256N10TFI023 Datasheet - Page 58
S29GL256N10TFI023
Manufacturer Part Number
S29GL256N10TFI023
Description
MirrorBit Flash Family
Manufacturer
ETC
Datasheet
1.S29GL256N10TFI023.pdf
(110 pages)
- Current page: 58 of 110
- Download datasheet (3Mb)
58
Reading Array Data
Reset Command
Autoselect Command Sequence
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the
erase-suspend-read mode, after which the system can read data from any non-
erase-suspended sector. After completing a programming operation in the Erase
Suspend mode, the system may once again read array data with the same ex-
ception. See the Erase Suspend/Erase Resume Commands section for more
information.
The system must issue the reset command to return the device to the read (or
erase-suspend-read) mode if DQ5 goes high during an active program or erase
operation, or if the device is in the autoselect mode. See the next section, Reset
Command, for more information.
See also Requirements for Reading Array Data in the Device Bus Operations sec-
tion for more information. The Read-Only Operations–“AC Characteristics”
section on page 88 provides the read parameters, and Figure 11 shows the timing
diagram.
Writing the reset command resets the device to the read or erase-suspend-read
mode. Address bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ignores reset commands until
the operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the device to the
read mode. If the program command sequence is written while the device is in
the Erase Suspend mode, writing the reset command returns the device to the
erase-suspend-read mode. Once programming begins, however, the device ig-
nores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to the read mode. If the device entered the autoselect mode
while in the Erase Suspend mode, writing the reset command returns the device
to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to the read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the sys-
tem must write the Write-to-Buffer-Abort Reset command sequence to reset the
device for the next operation.
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
Table
an alternative to that shown in Table 5, which is intended for PROM programmers
12
and Table
13
show the address and data requirements. This method is
S29GLxxxN MirrorBitTM Flash Family
A d v a n c e
I n f o r m a t i o n
27631A4 May 13, 2004
Related parts for S29GL256N10TFI023
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KLPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KQPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
BC41B143A05-IRK-E4BlueCpre 4-ROM Single Chip Bluetooth v2.0 System with EDR
Manufacturer:
ETC ETC
Datasheet: