S29GL512N SPANSION, S29GL512N Datasheet - Page 59
![no-image](/images/no-image-200.jpg)
S29GL512N
Manufacturer Part Number
S29GL512N
Description
Page Mode Flash Memory
Manufacturer
SPANSION
Datasheet
1.S29GL512N.pdf
(100 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S29GL512N
Manufacturer:
SPANSION
Quantity:
20 000
Company:
Part Number:
S29GL512N10FAA020
Manufacturer:
TDK-EPCOS
Quantity:
6 000
Company:
Part Number:
S29GL512N10FAI01
Manufacturer:
ARTESYN
Quantity:
2
Company:
Part Number:
S29GL512N10FAI020
Manufacturer:
SPANSION
Quantity:
14
Company:
Part Number:
S29GL512N10FFI01
Manufacturer:
SPANSION
Quantity:
10 447
Company:
Part Number:
S29GL512N10FFI01
Manufacturer:
SPANSION
Quantity:
60
Part Number:
S29GL512N10FFI012
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL512N10FFI02
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL512N10FFI020
Manufacturer:
SPANSION
Quantity:
20 000
Part Number:
S29GL512N10TAI010
Manufacturer:
SPANSION
Quantity:
20 000
D a t a
S h e e t
tion. If that occurs, the chip erase command sequence should be reinitiated once the device
has returned to reading array data, to ensure data integrity.
Figure 4, on page 58
illustrates the algorithm for the erase operation. Note that the Secured
Silicon Sector, autoselect, and CFI functions are unavailable when an erase opera-
tion in is progress. Refer to the table
Erase and Program Operations‚ on page 80
for
parameters, and
Figure 16, on page 82
section for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by
writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are
written, and are then followed by the address of the sector to be erased, and the sector erase
command.
Table 12 on page 63
and
Table 14 on page 65
shows the address and data require-
ments for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Embedded Erase
algorithm automatically programs and verifies the entire memory for an all zero data pattern
prior to electrical erase. The system is not required to provide any controls or timings during
these operations.
After the command sequence is written, a sector erase time-out of 50 µs occurs. During the
time-out period, additional sector addresses and sector erase commands may be written.
Loading the sector erase buffer may be done in any sequence, and the number of sectors may
be from one sector to all sectors. The time between these additional cycles must be less than
50 µs, otherwise erasure may begin. Any sector erase address and command following the
exceeded time-out may or may not be accepted. It is recommended that processor interrupts
be disabled during this time to ensure all commands are accepted. The interrupts can be
re-enabled after the last Sector Erase command is written. Any command other than Sec-
tor Erase or Erase Suspend during the time-out period resets the device to the read
mode. Note that the Secured Silicon Sector, autoselect, and CFI functions are un-
available when an erase operation in is progress. The system must rewrite the
command sequence and any additional addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See
DQ3:
Sector Erase Timer‚ on page
72.). The time-out begins from the rising edge of the final WE#
pulse in the command sequence.
When the Embedded Erase algorithm is complete, the device returns to reading array data
and addresses are no longer latched. The system can determine the status of the erase op-
eration by reading DQ7, DQ6, or DQ2 in the erasing sector. Refer to the Write Operation
Status section for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All
other commands are ignored. However, note that a hardware reset immediately terminates
the erase operation. If that occurs, the sector erase command sequence should be reinitiated
once the device has returned to reading array data, to ensure data integrity.
Figure 4, on page 58
illustrates the algorithm for the erase operation. Refer to the table
Erase
and Program Operations‚ on page 80
for parameters, and
Figure 16, on page 82
for timing
diagrams.
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit™ Flash Family
57