MT90823AG Zarlink Semiconductor, Inc., MT90823AG Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
MT90823AG
Manufacturer Part Number
MT90823AG
Description
Switch Fabric, 131.072Mbps Switching Bandwidth, 3.3V Supply Voltage, 120-PBGA
Manufacturer
Zarlink Semiconductor, Inc.
Datasheet
1.MT90823AG.pdf
(37 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT90823AG2
Manufacturer:
ZARLINK
Quantity:
32
JTAG Support
The MT90823 JTAG interface conforms to the IEEE
1149.1
Boundary-Scan Test
technique
boundary-scan circuitry is controlled by an external
test access port (TAP) Controller.
Test Access Port (TAP)
The Test Access Port (TAP) provides access to the
many test functions of the MT90823. It consists of
three input pins and one output pin. The following
pins comprise the TAP.
•
•
•
•
Test Clock Input (TCK)
TCK provides the clock for the test logic. The
TCK does not interfere with any on-chip clock
and thus remains independent. The TCK
permits shifting of test data into or out of the
Boundary-Scan register cells concurrently with
the operation of the device and without
interfering with the on-chip logic.
Test Mode Select Input (TMS)
The logic signals received at the TMS input are
interpreted by the TAP Controller to control the
test operations. The TMS signals are sampled
at the rising edge of the TCK pulse. This pin is
internally pulled to Vdd when it is not driven
from an external source.
Test Data Input (TDI)
Serial input data applied to this port is fed
either into the instruction register or into a test
data register, depending on the sequence
previously applied to the TMS input. Both
registers
section. The received input data is sampled at
the rising edge of TCK pulses. This pin is
internally pulled to Vdd when it is not driven
from an external source.
Test Data Output (TDO)
Depending on the sequence previously applied
to the TMS input, the contents of either the
instruction register or data register are serially
shifted out towards the TDO. The data out of the
TDO is clocked on the falling edge of the TCK
pulses. When no data is shifted through the
boundary scan cells, the TDO driver is set to a
high impedance state.
Boundary-Scan
it
are
specifies. The
described
(BST)
standard
design-for-testability
in
operation
a
subsequent
and
of
the
the
•
Instruction Register
In accordance with the IEEE 1149.1 standard, the
MT90823 uses public instructions. The MT90823
JTAG Interface contains a two-bit instruction register.
Instructions are serially loaded into the instruction
register from the TDI when the TAP Controller is in its
shifted-IR state. Subsequently, the instructions are
decoded to achieve two basic functions: to select the
test data register that may operate while the
instruction is current, and to define the serial test
data register path, which is used to shift data
between TDI and DO during data register scanning.
Test Data Register
As specified in IEEE 1149.1, the MT90823 JTAG
Interface contains three test data registers:
•
•
•
The MT90823 boundary scan register contains 118
bits. Bit 0 in Table 15 Boundary Scan Register is the
first bit clocked out. All tristate enable bits are active
high.
Test Reset (TRST)
Resets the JTAG scan structure. This pin is
internally pulled to VDD.
The Boundary-Scan Register
The Boundary-Scan register consists of a
series of Boundary-Scan cells arranged to form
a scan path around the boundary of the
MT90823 core logic.
The Bypass Register
The Bypass register is a single stage shift
register that provides a one-bit path from TDI to
its TDO.
The Device Identification Register
The device identification register is a 32-bit
register with the register contain of:
0000 0000 1000 0010 0011 0001 0100 1011
MSB
The LSB bit in the device identification register is
the first bit clocked out.
CMOS
MT90823
LSB
19