IDT72V265LA20PF IDT, Integrated Device Technology Inc, IDT72V265LA20PF Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT72V265LA20PF
Manufacturer Part Number
IDT72V265LA20PF
Description
IC FIFO SS 16384X18 20NS 64-TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Series
72Vr
Datasheet
1.IDT72V255LA10TFG.pdf
(27 pages)
Specifications of IDT72V265LA20PF
Function
Synchronous
Memory Size
288K (16K x 18)
Data Rate
50MHz
Access Time
20ns
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
72V265LA20PF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT72V265LA20PF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT72V265LA20PF8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
DESCRIPTION (CONTINUED)
Standard mode and First Word Fall Through (FWFT) mode.
on the data output lines unless a specific read operation is performed. A read
operation, which consists of activating REN and enabling a rising RCLK edge,
will shift the word from internal memory to the data output lines.
to the data output lines after three transitions of the RCLK signal. A REN does
not have to be asserted for accessing the first word. However, subsequent
words written to the FIFO do require a LOW on REN for access. The state of
the FWFT/SI input during Master Reset determines the timing mode in use.
can provide, the FWFT timing mode permits depth expansion by chaining
FIFOs in series (i.e. the data outputs of one FIFO are connected to the
corresponding data inputs of the next). No external logic is required.
FF/IR (Full Flag or Input Ready), HF (Half-full Flag), PAE (Programmable
Almost-Empty flag) and PAF (Programmable Almost-Full flag). The EF and
FF functions are selected in IDT Standard mode. The IR and OR functions
are selected in FWFT mode. HF, PAE and PAF are always available for use,
irrespective of timing mode.
memory. (See Table I and Table II.) Programmable offsets determine the flag
switching threshold and can be loaded by two methods: parallel or serial. Two
default offset settings are also provided, so that PAE can be set to switch at 127
or 1,023 locations from the empty boundary and the PAF threshold can be set
at 127 or 1,023 locations from the full boundary. These choices are made with
the LD pin during Master Reset.
IDT72V255LA/72V265LA 3.3 VOLT CMOS SuperSync FIFO™
8,192 x 18, 16,384 x 18
In IDT Standard mode, the first word written to an empty FIFO will not appear
In FWFT mode, the first word written to an empty FIFO is clocked directly
For applications requiring more data storage capacity than a single FIFO
PAE and PAF can be programmed independently to switch at any point in
There are two possible timing modes of operation with these devices: IDT
These FIFOs have five flag pins, EF/OR (Empty Flag or Output Ready),
FIRST WORD FALL THROUGH/SERIAL INPUT
PROGRAMMABLE ALMOST-FULL (PAF)
FULL FLAG/INPUT READY (FF/IR)
Figure 1. Block Diagram of Single 8,192 x 18 and 16,384 x 18 Synchronous FIFO
WRITE CLOCK (WCLK)
WRITE ENABLE (WEN)
SERIAL ENABLE(SEN)
DATA IN (D
PARTIAL RESET (PRS)
LOAD (LD)
(FWFT/SI)
0
- D
n
)
72V255LA
72V265LA
3
IDT
WCLK, are used to load the offset registers via the Serial Input (SI). For parallel
programming, WEN together with LD on each rising edge of WCLK, are used
to load the offset registers via Dn. REN together with LD on each rising edge
of RCLK can be used to read the offsets in parallel from Qn regardless of
whether serial or parallel offset loading has been selected.
pointers are set to the first location of the FIFO. The FWFT pin selects IDT
Standard mode or FWFT mode. The LD pin selects either a partial flag default
setting of 127 with parallel programming or a partial flag default setting of 1,023
with serial programming. The flags are updated according to the timing mode
and default offsets selected.
location of the memory. However, the timing mode, partial flag programming
method, and default or programmed offset settings existing before Partial Reset
remain unchanged. The flags are updated according to the timing mode and
offsets in effect. PRS is useful for resetting a device in mid-operation, when
reprogramming partial flags would be undesirable.
once. A LOW on the RT input during a rising RCLK edge initiates a retransmit
operation by setting the read pointer to the first location of the memory array.
automatically power down. Once in the power down state, the standby supply
current consumption is minimized. Initiating any operation (by activating control
inputs) will immediately take the device out of the power down state.
submicron CMOS technology.
MASTER RESET (MRS)
For serial programming, SEN together with LD on each rising edge of
During Master Reset (MRS) the following events occur: The read and write
The Partial Reset (PRS) also sets the read and write pointers to the first
The Retransmit function allows data to be reread from the FIFO more than
If, at any time, the FIFO is not actively performing an operation, the chip will
The IDT72V255LA/72V265LA are fabricated using IDT’s high speed
READ CLOCK (RCLK)
READ ENABLE (REN)
RETRANSMIT (RT)
EMPTY FLAG/OUTPUT READY (EF/OR)
PROGRAMMABLE ALMOST-EMPTY (PAE)
HALF FULL FLAG (HF)
DATA OUT (Q
OUTPUT ENABLE (OE)
0
- Q
n
)
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
4672 drw 03
OCTOBER 22, 2008