IDT72401L35P IDT, Integrated Device Technology Inc, IDT72401L35P Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT72401L35P
Manufacturer Part Number
IDT72401L35P
Description
IC FIFO PAR 64X4 35NS 16-DIP
Manufacturer
IDT, Integrated Device Technology Inc
Series
7200r
Datasheet
1.IDT72401L10SO8.pdf
(9 pages)
Specifications of IDT72401L35P
Function
Asynchronous
Memory Size
256 (64 x 4)
Access Time
35ns
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
16-DIP (0.300", 7.62mm)
Configuration
Dual
Density
256b
Word Size
4b
Organization
64x4
Sync/async
Asynchronous
Expandable
Yes
Bus Direction
Uni-Directional
Package Type
PDIP
Clock Freq (max)
Not RequiredMHz
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (max)
5.5V
Supply Current
35mA
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Through Hole
Pin Count
16
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Rate
-
Lead Free Status / Rohs Status
Not Compliant
Other names
72401L35P
INPUT DATA
FUNCTIONAL DESCRIPTION
to the traditional shift register approach. This FIFO architecture has a write
pointer, a read pointer and control logic, which allow simultaneous read and
write operations. The write pointer is incremented by the falling edge of the Shift
In (Sl) control; the read pointer is incremented by the falling edge of the Shift Out
(SO). The Input Ready (IR) signals when the FIFO has an available memory
location; Output Ready (OR) signals when there is valid data on the output.
Output Enable (OE) provides the capability of three-stating the FIFO outputs.
FIFO RESET
This causes the FlFO to enter an empty state, signified by Output Ready (OR)
being LOW and Input Ready (IR) being HIGH. In this state, the data outputs
(Q
DATA INPUT
input data into the first word location of the FIFO and causes Input Ready (IR)
to go LOW. On the HlGH-to-LOW transition of SI, the write pointer is moved to
the next word position and IR goes HIGH, indicating the readiness to accept new
data. If the FIFO is full, IR will remain LOW until a word of data is shifted out.
NOTES:
1. IR HIGH indicates space is available and a SI pulse may be applied.
2. Input Data is loaded into the first word.
3. IR goes LOW indicating the first word is full.
4. The write pointer is incremented.
5. The FIFO is ready for the next word.
6. If the FIFO is full then the IR remains LOW.
7. SI pulses applied while IR is LOW will be ignored (see Figure 4).
IDT72401/72403
CMOS PARALLEL FIFO 64 x 4, 64 x 5
INPUT DATA
The FIFO must be reset upon power up using the Master Reset (MR) signal.
0
The 64 x 4 FIFO is designed using a dual port RAM architecture as opposed
Data is shifted in on the LOW-to-HlGH transition of Shift In (Sl). This loads
-
3
) will be LOW.
IR
SI
IR
SI
(7)
t
IDS
(1)
(2)
t
SIH
t
IDH
STABLE DATA
Figure 3. The Mechanism of Shifting Data Into the FIFO
1/f
IN
t
SIL
(3)
Figure 2. Input Timing
5
DATA OUTPUT
the internal read pointer to be advanced to the next word location. If data is
present, valid data will appear on the outputs and Output Ready (OR) will go
HIGH. If data is not present, OR will stay LOW indicating the FIFO is empty. The
last valid word read from the FIFO will remain at the FlFOs output when it is empty.
When the FIFO is not empty, OR goes LOW on the LOW-to-HIGH transition of
SO. Previous data remains on the output until the HIGH-to-LOW transition of
SO).
FALL THROUGH MODE
FIFO. After a fall-through delay the data propagates to the output. When the
data reaches the output, the Output Ready (OR) goes HIGH. Fall-through mode
also occurs when the FIFO is completely full. When data is shifted out of the full
FIFO, a location is available for new data. After a fall-through delay, the Input
Ready (IR) goes HIGH. If Shift In (SI) is HIGH, the new data can be written
to the FIFO.
separate read and write pointers, the fall-through time (t
A word may be written into the FIFO on a clock cycle and can be accessed on
the next clock cycle.
Data is shifted out on the HlGH-to-LOW transition of Shift Out (SO). This causes
The FIFO operates in a fall-through mode when data gets shifted into an empty
Since these FlFOs are based on an internal dual-port RAM architecture with
t
IRL
(4)
1/f
IN
t
IRH
MILITARY AND COMMERCIAL
TEMPERATURE RANGES
(5)
PT
(6)
) is one cycle long.
2747 drw 06
2747 drw 07