DSP-A1092 ETC, DSP-A1092 Datasheet - Page 35
DSP-A1092
Manufacturer Part Number
DSP-A1092
Description
NATURAL SOUND AV AMPLIFIRE
Manufacturer
ETC
Datasheet
1.DSP-A1092.pdf
(71 pages)
- Current page: 35 of 71
- Download datasheet (773Kb)
the levels of the main, center, rear and front effect speakers.
your listening position with the remote control unit. Otherwise, the
result may not be satisfactory.
NOTE: Be sure to use the remote control unit with the lid open.
1. Set the TIME/LEVEL·SET MENU switch on the remote control to
the TIME/LEVEL position.
2. Depress the TEST key on the remote
control so that “TEST DOLBY SUR.” appears
on the display panel to enter test mode. A
hiss-like calibration signal should be heard
from the left main speaker, center speaker(s),
right main speaker, right rear speaker and left
rear speaker in turn (see diagram). Adjust the
master VOLUME to a normal listening level.
*
This operation uses an internal test-tone generator for balancing
The adjustment of each speaker output level should be done at
The state of test-tone output is shown on the display panel and
the monitor screen. (On the monitor screen, it is shown by an
image of audio listening room.) This is convenient for adjusting
each speaker level.
Left main
LEFT
LEFT
SURROUND
SPEAKER BALANCE ADJUSTMENT
Left rear
Remote control
CENTER
TIME/LEVEL
Center
SET MENU
RIGHT
SURROUND
Right rear
Remote control
Right main
RIGHT
TEST
3. Press the
adjust.
4. Adjust the level of the speaker selected in step 3 by pressing the
+ or – key so that it becomes almost as same as that of the main
speakers.
5. Repeat step 3 and 4 to adjust the level of other speakers.
* Whenever the
* If the CENTER SPEAKER mode is set to “PHNTM” (phantom),
* While adjusting, the test-tone is fixed on the selected speaker.
in turn as follows.
Pressing the
“CENTER” cannot be selected. (See page 30.)
CENTER
or
Center
key changes the speaker in the reverse order.
key to select the speaker whose level you will
key is pressed, the speaker selection changes
Remote control
Remote control
Right rear
R SUR.
L SUR.
Left rear
33
Related parts for DSP-A1092
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DIA SURGE SUPPRESSOR
Manufacturer:
Mitsubishi Electric Semiconductor
Datasheet:
Part Number:
Description:
DSP-Compatible Sampling Single/Dual ANALOG-TO-DIGITAL CONVERTERS
Manufacturer:
Burr-Brown Corporation
Datasheet:
Part Number:
Description:
DSP-Compatible Single/Dual DIGITAL-TO-ANALOG CONVERTERS
Manufacturer:
Burr-Brown Corporation
Datasheet:
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet: