TDA8029 Philips Semiconductors, TDA8029 Datasheet - Page 7

no-image

TDA8029

Manufacturer Part Number
TDA8029
Description
Low power single card reader
Manufacturer
Philips Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TDA8029H/101
Manufacturer:
PHI
Quantity:
430
Part Number:
TDA8029H/C101
Manufacturer:
PHI
Quantity:
102
Part Number:
TDA8029H/C101
Manufacturer:
PHI
Quantity:
1 000
Part Number:
TDA8029H101
Manufacturer:
JRC
Quantity:
96
Part Number:
TDA8029H101
Manufacturer:
PHI
Quantity:
1 000
Part Number:
TDA8029H101
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
TDA8029HL/07
Manufacturer:
PHILIPS
Quantity:
1 977
Part Number:
TDA8029HL/07
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
TDA8029HL/C103
Manufacturer:
SGMICRO
Quantity:
2 988
Part Number:
TDA8029HL/C103
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
TDA8029HL/C104
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
TDA8029HL/C104
Quantity:
6 922
Part Number:
TDA8029HL/C206,118
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
TDA8029HL/C207
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
TDA8029HL/C207
0
Part Number:
TDA8029HL/C207,118
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
8
Throughout this specification, it is assumed that the reader
is aware of ISO7816 norm terminology.
8.1
The embedded microcontroller is an 80C51FB with
internal 16 kbytes ROM, 256 bytes RAM and 512 bytes
XRAM. It has the same instruction set as the 80C51.
The controller is clocked by the frequency present on pin
XTAL1.
The controller may be reset by an active HIGH signal on
pin RESET, but it is also reset by the Power-on reset signal
generated by the supply supervisor.
The external interrupt INT0_N is used by the ISO UART,
by the analog drivers and the ETU counters. It must be left
open in the application.
The second external interrupt INT1_N is available for the
application.
2003 Oct 30
handbook, full pagewidth
Low power single card reader
FUNCTIONAL DESCRIPTION
Microcontroller
SDWN_N
PRES
CDEL
GND
V DD
P17
P16
I/O
1
2
3
4
5
6
7
8
Fig.2 Pin configuration.
TDA8029HL
7
A general description as well as added features are
described in this chapter.
The added features to the 80C51 controller are similar to
the 8XC51FB controller, except on the wake-up from
Power-down mode, which is possible by a falling edge on
INT0_N (card reader problem) or on INT1_N or on RX due
to the addition of an extra delay counter and enable
configuration bits within register UCR2 (see detailed
description in Section 8.10.3.2). For any further
information please refer to the published specification of
the 8XC51FB in “Data Handbook IC20; 80C51-Based 8-bit
Microcontrollers” .
The controller has four 8-bit I/O ports, three 16-bit
timer/event counters, a multi-source, four-priority-level,
nested interrupt structure, an enhanced UART and on-chip
oscillator and timing circuits. For systems that require
extra memory capability up to 64 kbytes, it can be
expanded using standard TTL-compatible memories and
logic.
19
18
17
24
23
22
21
20
FCE870
P27
PSEN_N
ALE
EA_N
TEST
SAM
PGND
SBM
Product specification
TDA8029

Related parts for TDA8029