TDA8029 Philips Semiconductors, TDA8029 Datasheet - Page 25

• Manufacturer Part Number: TDA8029
• Description: Low power single card reader
• Manufacturer: Philips Semiconductors

Philips Semiconductors
8.6
The TDA8029 has internal data memory that is mapped
into four separate segments.
The four segments, shown in Fig.9, are:
1. The lower 128 bytes of RAM (addresses 00h to 7Fh),
2. The upper 128 bytes of RAM (addresses 80h to FFh),
3. The Special Function Registers, SFRs, (addresses
4. The 512 bytes expanded RAM (XRAM 00h to 1FFh)
The lower 128 bytes can be accessed by either direct or
indirect addressing. The upper 128 bytes can be accessed
by indirect addressing only. The upper 128 bytes occupy
the same address space as the SFRs. That means they
have the same address, but are physically separate from
SFR space.
When an instruction accesses an internal location above
address 7Fh, the CPU knows whether the access is to the
upper 128 bytes of data RAM or to the SFR space by the
addressing mode used in the instruction. Instructions that
use direct addressing access SFR space. For example:
MOV A0h, #data accesses the SFR at location 0A0h
(which is register P2).
Instructions that use indirect addressing access the upper
128 bytes of data RAM. For example: MOV @R0, #data
where R0 contains 0A0h, accesses the data byte at
address 0A0h, rather than P2 (whose address is 0A0h).
2003 Oct 30
Low power single card reader
which are directly and indirectly addressable.
which are indirectly addressable only.
80h to FFh), which are directly addressable only.
are indirectly accessed by move external instructions,
MOVX, if the EXTRAM bit (bit 1 of register AUXR) is
cleared.
Expanded data RAM addressing
25
The XRAM can be accessed by indirect addressing, with
EXTRAM bit (register AUXR bit 1) cleared and MOVX
instructions. This part of memory is physically located
on-chip, logically occupies the first 512 bytes of external
data memory.
When EXTRAM = 0, the XRAM is indirectly addressed,
using the MOVX instruction in combination with any of the
registers R0, R1 of the selected bank or DPTR. An access
to XRAM will not affect ports P0, P3.6 (WR) and P3.7 (RD).
P2 is output during external addressing. For example:
MOVX @R0, A where R0 contains 0A0h, access the
EXTRAM at address 0A0h rather than external memory.
An access to external data memory locations higher than
1FFh (i.e., 0200h to FFFFh) will be performed with the
MOVX DPTR instructions in the same way as in the
standard 80C51, so with P0 and P2 as data/address bus,
and P3.6 and P3.7 as write and read timing signals.
When EXTRAM = 1, MOVX @Ri and MOVX @DPTR will
be similar to the standard 80C51. MOVX @Ri will provide
an 8-bit address multiplexed with data on port 0 and any
output port pins can be used to output higher order
address bits. This is to provide the external paging
capability. MOVX @DPTR will generate a 16-bit address.
Port 2 outputs the high order eight address bits (the
contents of DPH) while port 0 multiplexes the low-order
eight address bits (DPL) with data. MOVX @Ri and
MOVX @DPTR will generate either read or write signals
on P3.6 (WR) and P3.7 (RD).
The stack pointer (SP) may be located anywhere in the
256 bytes RAM (lower and upper RAM) internal data
memory. The stack must not be located in the XRAM.
Product specification
TDA8029