WM8955BL Wolfson Microelectronics, WM8955BL Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/7/716/wolfson_microelectronics_sml.jpg)
WM8955BL
Manufacturer Part Number
WM8955BL
Description
Stereo DAC
Manufacturer
Wolfson Microelectronics
Datasheet
1.WM8955BL.pdf
(44 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
WM8955BL
Manufacturer:
WOLFSON
Quantity:
20 000
Company:
Part Number:
WM8955BLGECO/RV
Manufacturer:
WOLFSON
Quantity:
50 000
Part Number:
WM8955BLGECO/RV
Manufacturer:
WM
Quantity:
20 000
Part Number:
WM8955BLGECO/V
Manufacturer:
WOLFSON
Quantity:
20 000
w
Production Data
CONTROL INTERFACE
SELECTION OF CONTROL MODE
The WM8955BL is controlled by writing to registers through a serial control interface. A control word
consists of 16 bits. The first 7 bits (B15 to B9) are address bits that select which control register is
accessed. The remaining 9 bits (B8 to B0) are register bits, corresponding to the 9 bits in each control
register. The control interface can operate as either a 3-wire or 2-wire MPU interface. The MODE pin
selects the interface format.
Table 24 Control Interface Mode Selection
3-WIRE SERIAL CONTROL MODE
In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on
CSB latches in a complete control word consisting of the last 16 bits.
Figure 18 3-Wire Serial Control Interface
2-WIRE SERIAL CONTROL MODE
The WM8955BL supports software control via a 2-wire serial bus. Many devices can be controlled by
the same bus, and each device has a unique 7-bit address (this is not the same as the 7-bit address
of each register in the WM8955BL).
The WM8955BL operates as a slave device only. The controller indicates the start of data transfer
with a high to low transition on SDIN while SCLK remains high. This indicates that a device address
and data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next
eight bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches
the address of the WM8955BL and the R/W bit is ‘0’, indicating a write, then the WM8955BL responds
by pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is
‘1’, the WM8955BL returns to the idle condition and wait for a new start condition and valid address.
Once the WM8955BL has acknowledged a correct address, the controller sends the first byte of
control data (B15 to B8, i.e. the WM8955BL register address plus the first bit of register data). The
WM8955BL then acknowledges the first data byte by pulling SDIN low for one clock pulse. The
controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register
data), and the WM8955BL acknowledges again by pulling SDIN low.
The transfer of data is complete when there is a low to high transition on SDIN while SCLK is high.
After receiving a complete address and data sequence the WM8955BL returns to the idle state and
waits for another start condition. If a start or stop condition is detected out of sequence at any point
during data transfer (i.e. SDIN changes while SCLK is high), the device jumps to the idle condition.
SCLK
SDIN
CSB
MODE
High
Low
B15
B14
control register address
B13
B12
INTERFACE FORMAT
B11
2 wire
3 wire
B10
B9
B8
B7
B6
control register data bits
B5
B4
PD Rev 4.1 February 2007
B3
B2
WM8955BL
B1
B0
latch
33