ATA25 White Electronic Designs Corporation, ATA25 Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
ATA25
Manufacturer Part Number
ATA25
Description
Density = 32MB-1GB ;; Memory Device = Hitachi Flash ;; Organization = X16/x8 ;; Speed (ns) = 250 ;; Volt = 3/5 ;;
Manufacturer
White Electronic Designs Corporation
Datasheet
1.ATA25.pdf
(62 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATA2501
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA2508
Manufacturer:
ATL
Quantity:
20 000
Company:
Part Number:
ATA2508DA-20S
Manufacturer:
ATLAB
Quantity:
4 546
Part Number:
ATA2508DA-24S
Manufacturer:
ATLAB
Quantity:
20 000
Company:
Part Number:
ATA2508DA-32N
Manufacturer:
ATMEL
Quantity:
6 630
Part Number:
ATA2508DA-32N
Manufacturer:
ATLAB
Quantity:
20 000
Company:
Part Number:
ATA2508DC-30S
Manufacturer:
ICT
Quantity:
396
Company:
Part Number:
ATA2508DC-32N
Manufacturer:
ATL
Quantity:
26 203
Company:
Part Number:
ATA2511DB-IAC
Manufacturer:
ATLab
Quantity:
3 050
Part Number:
ATA2538DC-16P
Manufacturer:
ATLAB
Quantity:
20 000
June 2000 Rev. 1 – ECO #12936
12. Device control register: This register is a write only register, and it is used for controlling the card
interrupt request and issuing an ATA soft reset to the card.
bit7
bit
7 to 4
3
2
1
0
13. Drive Address register: This register is a read only register, and it is used for confirming the drive
status. This register provides for compatibility with the AT disk drive interface. It is recommended that
this register not be mapped into the host’s I/O space because of potential conflicts on bit7.
bit7
bit
7
6
5 to 2 nHS3-0 (Head Select3-0)
1
0
ATA Command Specifications
This table summarizes the ATA command set with the paragraphs. The following shows the support
commands and command codes which are written in the command registers.
7PxxxATA25xxC25
Name
1
SRST (Software ReSeT)
nIEN (Interrupt ENable)
0
Name
nWTG (WriTing Gate)
nDS1 (Idrive Select1)
nDS0 (Idrive Select0)
bit6
bit6
nWTG
bit5
bit5
nHS3
bit4
bit4
nHS2
Function
don't care
This bit is set to "1".
Reset operation. This does not change the Card Configuration
registers as a Hardware Reset does. The card remains in Reset
until this bit is reset to "0".
is enabled. When this bit is set to "1", -IREQ is disabled.
This bit is set to "0".
Function
This bit is unknown
This bit is unknown
theDrive/Head register.
This bit is set to "1" in order to force the card to perform Task File
This bit is used for enabling -IREQ. When this bit is set to "0", -IREQ
These bits are the negative value of Head Select bits (bit 3 to 0) in
This bit is unknown
This bit is unknown
36
bit3
1
bit3
nHS1
White Electronic Designs Corporation (508) 366-5151
bit2
SRST
bit2
nHS0
bit1
nIEN
bit1
nDS1
bit0
0
bit0
nDS0