MAX106CHC Maxim, MAX106CHC Datasheet - Page 5

• Manufacturer Part Number: MAX106CHC
• Description: 5V / 600Msps / 8-Bit ADC with On-Chip 2.2GHz Bandwidth Track/Hold Amplifier
• Manufacturer: Maxim

AC ELECTRICAL CHARACTERISTICS (continued)
(V
unless otherwise noted.)
Note 1: Static linearity parameters are computed from a “best-fit” straight line through the code transition points. The full-scale
Note 2: The offset control input is a self-biased voltage divider from the internal +2.5V reference voltage. The nominal open-circuit
Note 3: The clock input’s termination voltage can be operated between -2.0V and GNDI. Observe the absolute maximum ratings on
Note 4: Input logic levels are measured with respect to the V
Note 5: All PECL digital outputs are loaded with 50Ω to V
Note 6: The current in the V
Note 7: Common-mode rejection ratio is defined as the ratio of the change in the transfer-curve offset voltage to the change in the
Note 8: Measured with the positive supplies tied to the same potential, V
Note 9: V
Note 10: Power-supply rejection ratio is defined as the ratio of the change in the transfer-curve offset voltage to the change in power
Note 11: Effective number of bits (ENOB) and signal-to-noise plus distortion (SINAD) are computed from a curve fit referenced to the
TIMING CHARACTERISTICS
Maximum Sample Rate
Clock Pulse Width Low
Clock Pulse Width High
Aperture Delay
Aperture Jitter
Reset Input Data Setup Time
(Note 13)
Reset Input Data Hold Time
(Note 13)
CLK to DREADY Propagation
Delay
DREADY to DATA Propagation
Delay (Note 14)
DATA Rise Time
DATA Fall Time
DREADY Rise Time
DREADY Fall Time
Primary Port Pipeline Delay
Auxiliary Port Pipeline Delay
CC
A = V
range (FSR) is defined as 256
voltage is +1.25V. It may be driven from an external potentiometer connected between REFOUT and GNDI.
the CLK+ and CLK- inputs.
supply voltage.
tion of the load resistance and the V
common-mode voltage, expressed in dB.
supply voltage, expressed in dB.
theoretical full-scale range.
PARAMETER
CC
EE
I = V
varies from -5.25V to -4.75V.
CC
D = +5.0V, V
_______________________________________________________________________________________
2.2GHz Bandwidth Track/Hold Amplifier
±5V, 600Msps, 8-Bit ADC with On-Chip
CC
O power supply does not include the current in the digital output’s emitter followers, which is a func-
EE
SYMBOL
t
t
RDREADY
FDREADY
= -5.0V, V
t
t
RDATA
FDATA
t
f
t
t
t
t
t
PWH
MAX
PLW
t
t
t
PD1
PD2
PDP
PDA
t
HD
AD
SU
AJ
·
slope of the line.
TT
CC
Figure 17
Figure 17
Figure 17
Figure 4
Figure 15
Figure 15
Figure 17
Figure 17
20% to 80%, C
20% to 80%, C
20% to 80%, C
20% to 80%, C
Figures 6, 7, 8
Figures 6, 7, 8
termination voltage.
O = +3.3V, REFIN connected to REFOUT, f
CC
O - 2.0V. Measurements are made with respect to the V
CC
L
L
L
L
CONDITIONS
= 3pF
= 3pF
= 3pF
= 3pF
O power-supply voltage.
DIV1, DIV2 modes
DIV4 mode
DIV1, DIV2 modes
DIV4 mode
CC
A = V
CC
D = V
CC
S
I. V
= 600Msps, f
CC
0.75
0.75
MIN
600
-50
0
0
varies from +4.75V to +5.25V.
< 0.5
TYP
IN
100
150
420
360
220
180
2.2
7.5
7.5
8.5
9.5
at -1dBFS, T
MAX
CC
350
5
O power-
A
= +25°C,
Cycles
Cycles
UNITS
Clock
Clock
Msps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ns
ns
ns
5