MAX104 Maxim, MAX104 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
MAX104
Manufacturer Part Number
MAX104
Description
5V / 1Gsps / 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier
Manufacturer
Maxim
Datasheet
1.MAX104.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX1040BETX
Manufacturer:
TOSHIBA
Quantity:
7
Company:
Part Number:
MAX1044CPA
Manufacturer:
MAXIM
Quantity:
5 510
Part Number:
MAX1044CPA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1044CPA+
Manufacturer:
Maxim Integrated Products
Quantity:
1 933
Part Number:
MAX1044CSA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044CSA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044ESA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044ESA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
REFOUT to REFIN. This connects the reference output
to the positive input of the reference buffer. The buffer’s
negative input is internally connected to GNDR. GNDR
must be connected to GNDI on the user’s application
board. REFOUT can source up to 2.5mA to supply
external devices if required.
An adjustable external reference can be used to adjust
the ADC’s full-scale range. To use an external refer-
ence supply, simply connect a high-precision reference
to the REFIN pin and leave the REFOUT pin floating. In
this configuration, REFOUT must not be simultaneously
connected to avoid conflicts between the two refer-
ences. REFIN has a typical input resistance of 5kΩ and
accepts input voltages of +2.5V ±200mV. Using the
MAX104’s internal reference is recommended for best
performance.
The MAX104 provides data in offset binary format to dif-
ferential PECL outputs. A simplified circuit schematic of
the PECL output cell is shown in Figure 5. All PECL out-
puts are powered from V
from any voltage between +3.0V to V
interfacing with either +3.3V or +5V systems. The nomi-
nal V
All PECL outputs on the MAX104 are open-emitter
types and must be terminated at the far end of each
transmission line with 50Ω to V
MAX104 PECL outputs and their functions.
±5V, 1Gsps, 8-Bit ADC with
On-Chip 2.2GHz Track/Hold Amplifier
Table 1. PECL Output Functions
14
A0+, A0-, A1+, A1-, A2+, A2-,
A3+, A3-, A4+, A4-, A5+, A5-,
P0+, P0-, P1+, P1-, P2+, P2-,
P3+, P3-, P4+, P4-, P5+, P5-,
PECL OUTPUT SIGNALS
CC
______________________________________________________________________________________
DREADY+, DREADY-
RSTOUT+, RSTOUT-
O supply voltage is +3.3V.
A6+, A6-, A7+, A7-
P6+, P6-, P7+, P7-
OR+, OR-
CC
O, which may be operated
CC
O - 2V. Table 1 lists all
Primary-Port Differential Outputs from LSB to MSB. A “+” indicates the true outputs; a “-”
denotes the complementary outputs.
Auxiliary-Port Differential Outputs from LSB to MSB. A “+” indicates the true outputs; a “-”
denotes the complementary outputs.
Data-Ready Clock True and Complementary Outputs. These signal lines are used to latch
the output data from the primary to the auxiliary output ports. Data changes on the rising
edge of the DREADY clock.
Overrange True and Complementary Outputs
Reset Output True and Complementary Outputs
Digital Outputs
CC
D for flexible
The MAX104 features an internal data demultiplexer
that provides for three different modes of operation (see
the following sections on Demultiplexed DIV2 Mode,
Non-Demultiplexed DIV1 Mode, and Decimation DIV4
Mode ) controlled by two TTL/CMOS-compatible inputs:
DEMUXEN and DIVSELECT.
DEMUXEN enables or disables operation of the internal
1:2 demultiplexer. A logic high on DEMUXEN activates
the internal demultiplexer, and a logic low deactivates
it. With the internal demultiplexer enabled, DIVSELECT
controls the selection of the operational mode. DIVSE-
LECT low selects demultiplexed DIV2 mode, and DIV-
SELECT high selects decimation DIV4 mode (Table 2).
Figure 5. Simplified PECL Output Structure
FUNCTIONAL DESCRIPTION
500
GNDD
DIFF.
PAIR
1.8mA
500
Demultiplexer Operation
GNDD
GNDD
V
A_+/P_+
A_-/P_-
CC
O