MAX104 Maxim, MAX104 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
MAX104
Manufacturer Part Number
MAX104
Description
5V / 1Gsps / 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier
Manufacturer
Maxim
Datasheet
1.MAX104.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX1040BETX
Manufacturer:
TOSHIBA
Quantity:
7
Company:
Part Number:
MAX1044CPA
Manufacturer:
MAXIM
Quantity:
5 510
Part Number:
MAX1044CPA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1044CPA+
Manufacturer:
Maxim Integrated Products
Quantity:
1 933
Part Number:
MAX1044CSA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044CSA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044ESA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1044ESA+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
The MAX104’s flash or parallel architecture provides
the fastest multibit conversion of all common integrated
ADC designs. The key to this high-speed flash archi-
tecture is the use of an innovative, high-performance
comparator design. The flash converter and down-
stream logic translate the comparator outputs into a
parallel 8-bit output code and pass this binary code on
to the optional 8:16 demultiplexer, where primary and
auxiliary ports output PECL-compatible data at up to
500Msps per port (depending on how the demultiplex-
er section is set on the MAX104).
The ideal transfer function appears in Figure 2.
As with all ADCs, if the input waveform is changing
rapidly during conversion, effective number of bits
(ENOB) and signal-to-noise ratio (SNR) specifications
will degrade. The MAX104’s on-chip, wide-bandwidth
(2.2GHz) T/H amplifier reduces this effect and increases
the ENOB performance significantly, allowing precise
capture of fast analog data at high conversion rates.
The T/H amplifier buffers the input signal and allows a
full-scale signal input range of ±250mV. The T/H ampli-
fier’s differential 50Ω input termination simplifies inter-
facing to the MAX104 with controlled impedance lines.
Figure 3 shows a simplified diagram of the T/H amplifier
stage internal to the MAX104.
Aperture width, delay, and jitter (or uncertainty) are
parameters that affect the dynamic performance of
high-speed converters. Aperture jitter, in particular,
directly influences SNR and limits the maximum slew
rate (dV/dt) that can be digitized without contributing
significant errors. The MAX104’s innovative T/H amplifier
design limits aperture jitter typically to less than 0.5ps.
Aperture width (t
(Figure 4) to disconnect the hold capacitor from the
input circuit (for instance, to turn off the sampling
bridge and put the T/H unit in hold mode).
Aperture jitter (t
(Figure 4) in the time between the samples.
Aperture delay (t
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 4).
The MAX104 features an on-chip +2.5V precision
bandgap reference, which can be used by connecting
AJ
AW
AD
On-Chip Track/Hold Amplifier
______________________________________________________________________________________
) is the sample-to-sample variation
) is the time the T/H circuit requires
) is the time defined between the
On-Chip 2.2GHz Track/Hold Amplifier
Principle of Operation
Internal Reference
Aperture Width
Aperture Delay
Aperture Jitter
±5V, 1Gsps, 8-Bit ADC with
Figure 2. Transfer Function
Figure 3. Internal Structure of the 2.2GHz T/H Amplifier
Figure 4. T/H Aperture Timing
ALL INPUTS ARE ESD PROTECTED
(NOT SHOWN IN THIS
SIMPLIFIED DRAWING).
CLKCOM
OVERRANGE +
CLK+
CLK-
VIN+
VIN-
50
50
DATA (T/H)
SAMPLED
ANALOG
GNDI
INPUT
255
255
254
129
128
127
126
CLK
CLK
T/H
3
2
1
0
t
AD
50
50
TRACK
AMPLIFIER
SPLITTER
CLOCK
INPUT
APERTURE DELAY (t
APERTURE WIDTH (t
APERTURE JITTER (t
ANALOG INPUT
SAMPLING
BRIDGE
t
t
AW
HOLD
AJ
0
GNDI
AD
AJ
AW
AMPLIFIER
C
)
)
BUFFER
)
TO
COMPARATORS
HOLD
TRACK
TO
COMPARATORS
13