M25PX64-STVME6E Numonyx, B.V., M25PX64-STVME6E Datasheet - Page 45
![no-image](/images/no-image-200.jpg)
M25PX64-STVME6E
Manufacturer Part Number
M25PX64-STVME6E
Description
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer
Numonyx, B.V.
Datasheet
1.M25PX64-STVME6E.pdf
(66 pages)
- Current page: 45 of 66
- Download datasheet (2Mb)
M25PX64
6.13
Program OTP instruction (POTP)
The program OTP instruction (POTP) is used to program at most 64 bytes to the OTP
memory area (by changing bits from ‘1’ to ‘0’, only). Before it can be accepted, a write
enable (WREN) instruction must previously have been executed. After the write enable
(WREN) instruction has been decoded, the device sets the write enable latch (WEL) bit.
The program OTP instruction is entered by driving Chip Select (S) Low, followed by the
instruction opcode, three address bytes and at least one data byte on serial data input
(DQ0).
Chip Select (S) must be driven High after the eighth bit of the last data byte has been
latched in, otherwise the program OTP instruction is not executed.
There is no rollover mechanism with the program OTP (POTP) instruction. This means that
the program OTP (POTP) instruction must be sent with a maximum of 65 bytes to program,
once all 65 bytes have been latched in, any following byte will be discarded.
The instruction sequence is shown in
As soon as Chip Select (S) is driven High, the self-timed page program cycle (whose
duration is t
may be read to check the value of the write in progress (WIP) bit. The write in progress
(WIP) bit is 1 during the self-timed program OTP cycle, and it is 0 when it is completed. At
some unspecified time before the cycle is complete, the write enable latch (WEL) bit is reset.
To lock the OTP memory:
Bit 0 of the OTP control byte, that is byte 64, (see
OTP memory array.
Once a bit of the OTP memory has been programmed to ‘0’, it can no longer be set to ‘1’.
Therefore, as soon as bit 0 of byte 64 (control byte) is set to ‘0’, the 64 bytes of the OTP
memory array become read-only in a permanent way.
Any program OTP (POTP) instruction issued while an erase, program or write cycle is in
progress is rejected without having any effect on the cycle that is in progress.
When bit 0 of byte 64 = ’1’, the 64 bytes of the OTP memory array can be programmed.
When bit 0 of byte 64 = ‘0’, the 64 bytes of the OTP memory array are read-only and
cannot be programmed anymore.
PP
) is initiated. While the program OTP cycle is in progress, the status register
Figure
20.
Figure
21) is used to permanently lock the
Instructions
45/66
Related parts for M25PX64-STVME6E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![M25PX64-SOVME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PX64-VME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PE16-VMW6P](/images/no-image3.png)
Part Number:
Description:
16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-A](/images/no-image3.png)
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-AVMP6TP](/images/no-image3.png)
Part Number:
Description:
512-Kbit, serial flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-A](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMB6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMN6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMP6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128-VME6TP](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VME6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VMP6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P20-VMN6TP/X](/images/no-image3.png)
Part Number:
Description:
2 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet: