M25PX64-STVME6E Numonyx, B.V., M25PX64-STVME6E Datasheet - Page 34
![no-image](/images/no-image-200.jpg)
M25PX64-STVME6E
Manufacturer Part Number
M25PX64-STVME6E
Description
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer
Numonyx, B.V.
Datasheet
1.M25PX64-STVME6E.pdf
(66 pages)
- Current page: 34 of 66
- Download datasheet (2Mb)
Instructions
6.5
34/66
Write status register (WRSR)
The write status register (WRSR) instruction allows new values to be written to the status
register. Before it can be accepted, a write enable (WREN) instruction must previously have
been executed. After the write enable (WREN) instruction has been decoded and executed,
the device sets the write enable latch (WEL).
The write status register (WRSR) instruction is entered by driving Chip Select (S) Low,
followed by the instruction code and the data byte on serial data input (DQ0).
The instruction sequence is shown in
The write status register (WRSR) instruction has no effect on b6, b1 and b0 of the status
register. b6 is always read as ‘0’.
Chip Select (S) must be driven High after the eighth bit of the data byte has been latched in.
If not, the write status register (WRSR) instruction is not executed. As soon as Chip Select
(S) is driven High, the self-timed write status register cycle (whose duration is t
While the write status register cycle is in progress, the status register may still be read to
check the value of the write in progress (WIP) bit. The write in progress (WIP) bit is 1 during
the self-timed write status register cycle, and is 0 when it is completed. When the cycle is
completed, the write enable latch (WEL) is reset.
The write status register (WRSR) instruction allows the user to change the values of the
block protect (BP2, BP1, BP0) bits, to define the size of the area that is to be treated as
read-only, as defined in
user to set and reset the status register write disable (SRWD) bit in accordance with the
Write Protect (W/V
(W/V
status register (WRSR) instruction is not executed once the hardware protected mode
(HPM) is entered.
Figure 12. Write status register (WRSR) instruction sequence
PP
) signal allow the device to be put in the hardware protected mode (HPM). The write
S
C
DQ0
DQ1
PP
) signal. The status register write disable (SRWD) bit and Write Protect
Table
0
1
High Impedance
3. The write status register (WRSR) instruction also allows the
2
Instruction
3
4
Figure
5
6
12.
7
MSB
7
8
6
9 10 11 12 13 14 15
5
register in
4
Status
3
2
1
0
AI13735
W
) is initiated.
M25PX64
Related parts for M25PX64-STVME6E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![M25PX64-SOVME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PX64-VME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PE16-VMW6P](/images/no-image3.png)
Part Number:
Description:
16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-A](/images/no-image3.png)
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-AVMP6TP](/images/no-image3.png)
Part Number:
Description:
512-Kbit, serial flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-A](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMB6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMN6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMP6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128-VME6TP](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VME6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VMP6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P20-VMN6TP/X](/images/no-image3.png)
Part Number:
Description:
2 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet: