M25PX64-STVME6E Numonyx, B.V., M25PX64-STVME6E Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
M25PX64-STVME6E
Manufacturer Part Number
M25PX64-STVME6E
Description
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer
Numonyx, B.V.
Datasheet
1.M25PX64-STVME6E.pdf
(66 pages)
- Current page: 18 of 66
- Download datasheet (2Mb)
Operating features
4.9
18/66
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence. However, taking this signal Low does not terminate any
write status register, program or erase cycle that is currently in progress.
To enter the hold condition, the device must be selected, with Chip Select (S) Low.
The hold condition starts on the falling edge of the Hold (HOLD) signal, provided that this
coincides with Serial Clock (C) being Low (as shown in
The hold condition ends on the rising edge of the Hold (HOLD) signal, provided that this
coincides with Serial Clock (C) being Low.
If the falling edge does not coincide with Serial Clock (C) being Low, the hold condition
starts after Serial Clock (C) next goes Low. Similarly, if the rising edge does not coincide
with Serial Clock (C) being Low, the hold condition ends after Serial Clock (C) next goes
Low (this is shown in
During the hold condition, the serial data output (DQ1) is high impedance, and serial data
input (DQ0) and Serial Clock (C) are don’t care.
Normally, the device is kept selected, with Chip Select (S) driven Low, for the whole duration
of the hold condition. This is to ensure that the state of the internal logic remains unchanged
from the moment of entering the hold condition.
If Chip Select (S) goes High while the device is in the Hold condition, this has the effect of
resetting the internal logic of the device. To restart communication with the device, it is
necessary to drive Hold (HOLD) High, and then to drive Chip Select (S) Low. This prevents
the device from going back to the hold condition.
Figure 6.
HOLD
C
Hold condition activation
Figure
6).
(standard use)
condition
Hold
Figure
(non-standard use)
6).
condition
Hold
M25PX64
AI02029D
Related parts for M25PX64-STVME6E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![M25PX64-SOVME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PX64-VME6E](/images/no-image3.png)
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25PE16-VMW6P](/images/no-image3.png)
Part Number:
Description:
16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-A](/images/no-image3.png)
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P05-AVMP6TP](/images/no-image3.png)
Part Number:
Description:
512-Kbit, serial flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-A](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMB6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMN6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P10-AVMP6TP/X](/images/no-image3.png)
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P128-VME6TP](/images/no-image3.png)
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VME6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P16-VMP6TP](/images/no-image3.png)
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
![M25P20-VMN6TP/X](/images/no-image3.png)
Part Number:
Description:
2 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet: